Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Allied Maxcut Series 4 Holders

Diameter range: 46.99 to 65.28mm.

For all dimensional specifications please refer to our catalogue.

Flanged Straight Shank

Starrett Bi-Metal Holesaws Constant Pitch HSS

Bi-Metal Constant Pitch Holesaws have 6 teeth per 25mm/inch with an aggressive cutting action, featuring a HSS cutting edge welded to a tough alloy steel body. The Constant Pitch provides a smooth cut on thinner gauge materials, with minimal tendency to bite or snag on contact with irregular surfaces. Cutting depth 41mm (1 5/8").

Holesaw and Arbor sizes:
14-25mm - use Arbor A4 or K4.
30-210mm - use Arbor A10 or K10.

Constant Pitch Bi-Metal HSS Holesaws

Indexa-Seiki? Screw-On External Toolholders

For further technical and dimensional specifications please refer to our catalogue.

SVLB - Left Hand

95 Approach for 5 positive 35 rhombic inserts.

Dormer Stub Drills

A920 - HSCo PFX Stub Drills
High productivity "one-hit" drilling to 3xD. Excellent performance across a wide range of materials. Parabolic flute design promotes constant chip flow.Size Range: 1.0-20.0mm. Manufactured to BS 323, DIN1897, ansi.

A920 - HSCo PFX Stub Drills - metric

A920
Excellent for:
Carbon/alloy steels, stainless, titanium and nickel

Good for:
Cast iron, copper, aluminium and thermoplastics

Dormer Machine Taps

Dormer machine tap ranges have been designed for use with a high quality floating tool holder. For synchronous tapping on CNC machines with a rigid tapping cycle, Dormer SynchroFlex tool holders are recommended for a precisely defined minimum compensation in order to maximise machine performance. This is particularly important for larger sizes of spiral flute taps.

Available in spiral point for through holes and spiral flute for blind holes with 45 spiral angle. The three radii profile, with a constant rake angle all along the flute, is specially designed to give an optimum performance and chip evacuation in materials being threaded.
Surface Treatment
Special gold finish with bright flutes/thread, or steam tempering (blue) guarantee a smooth cutting action with less build up on the cutting edge.

Manufactured from HSS-XS1 premium quality vanadium powder steel and HSCo for superior toughness and edge strength, to give a high resistance to wear and long tool life.

All taps are available in Metric thread form initially. Thread forms Metric Fine, UNC, UNF and G will be stocked from September 2010.
Short Thread Length
The short thread length means low torque and better chip evacuation.
Thread Depth
Threading to depths of up to 2.5 x Diameter.

EP00 Series Spiral Point Metric Machine Tap

Dormer Spiral Point Metric Machine Taps for through holes. With gold finish with bright flutes.
Taper lead to DIN form B.
Tapping tolerance to 6H.
Max depth 2.5 x D.

Walton Replacement Fingers for 4 Flute Extractors

Thoroughly remove all chips of the broken tap. insert the extractor fingers into the flutes of the broken tap, pushing them gently but firmly into position. Push the holder down until it touches the broken tap. slide the sleeve down until it touches the work. Apply a tap wrench to the square end of the holder. Twist forward and backward a few times to loosen, then back out the broken tap.



Supplied Individually.

Starrett Bandsaw Blades

Super Flex-Back is recommended for general-purpose cutting at an attractive cost on easy to machine materials; blades have excellent fatigue endurance to give long life on machines running at a high surface feet per minute. High carbon/chromium `pinpoint carbide` tool steel. Hardened and tempered tooth tips - 64/66 Rockwell C Hardness. Economical, general-purpose cutting. Recommended applications: light section low alloy steels, ferrous and non-ferrous metals, plastics, furniture and composition board.

Starratt Bandsaw Blades

Kennedy Holesaws Constant Pitch Bi-Metal HSS

Featuring a constant pitch - first choice for cutting thin sheet materials up to 3mm thick. For producing high quality holes in wood, steel, brass, bronze, cast iron, aluminium and plastic. Featuring an hardened HSS cutting edge welded to a tough alloy steel body. Heavy duty shatter-resistant construction; virtually unbreakable.

6 teeth per inch.
38mm (1,1/2") cutting depth.

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

For the complete range of Holesaws and Arbors, please refer to our catalogue.

Sherwood 2 Flute Long Series Slot Drills Threaded Shank HSS

Used for milling keyways and slots in one unit. Bright Finish. Flute Type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

For all dimensional specifications please refer to our catalogue.

Metric