Carbide Grade AC2000 (P15 - P30)

Al2O3 Coated Grade
For general to rough cutting of steels.

NSU Chipbreaker

Application: finishing ~ light cut.

SwissTech 2 Flute Slot Drills Weldon Shank HSS-Co 8%

Centre cutting. Weldon shank to DIN 1835B. Cutting diameter to e8. Shank diameter to h6. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 03 Long SDN-2WL TiCN Coated

Dimensions to DIN 844.

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Kennedy Needle File Sets

Supplied in PVC Wallet. Manufactured to BS 498:1990. Cut 2. Available in a 6 or 12 piece set in either 14cm or 16cm.

16cm Needle File 6 Piece Set

Contents:
1x Flat.
1x Hand.
1x Half Round.
1x Round.
1x Square.
1x Three Square.

Guhring Production Drills

Guhring No.5523 Jobber Drill HSS-Co have a tough cobalt substrate that delivers high performance at low cost to produce a general purpose drill for the machining of steel and cast steel (alloyed and unalloyed), , grey cast iron, malleable cast iron, spheroidal graphite iron, sintered iron and graphite with high concentricity characteristics.

No.5523 Jobber Drill HSS-Co

Sherwood Long Series Drills HSS

General-purpose high speed steel long series drills are designed for deep hole drilling of most materials. The drill has the same diameter on both the fluted section and the shank. Manufactured to BS328;Part 1:1986, DIN340RN, ISO494.

For all dimensional specifications please refer to our catalogue.

Series L100 - Inch

Sumitomo T-Rex Carbide Inserts

The Sumitomo T-Rex can replace your costly DNMG applications with the economical T-REX System!

Features & Benefits
55 triangle insert.
6 cutting edges versus the standard 4 edges of a DNMG insert.
Rigid clamping system ensures accurate insert indexing.
Up to 2.5mm (0.100") depth of cut.
Available in the -LU and ?GU chipbreakers with grades AC700G, AC2000 and AC3000.
Suitable for all steels including stainless.

T-Rex TRM55 Carbide Insert

Chip Breaker:
LU Type Finishing Breaker
DOC 0.25mm-1.75mm
Fz 0.025-0.4mm/rev

Grade Description: T3000Z (Steels) Tough cermet grade for medium and interrupted cutting.
Serration.

Carbide Grade AC2000 (P15 - P30)

Al2O3 Coated Grade
For general to rough cutting of steels.

NGU Chipbreaker

Application: medium materials.

Dormer Stub Drills HSS TiN Tip Coated

Designed for increased productivity and tool life compared to standard stub drills. TiN coating has been applied to 35%-50% of the flute length (dependent on drill diameter) to keep cost down and lower the cost per hole. The 135 split point is advantageous for the pre-drilling of rivets and for drilling in sheet metal. Suitable for drilling alloy steel, carbon steels, cast iron, titanium and aluminium. Manufactured to DIN1897, ANSI.

Series A022 Stub Drill HSS TiN Tip Coated - Metric

Swisstech Fine Pitch Ripper Cutters Weldon Shank HSS-E PM TiALN Coated

Centre cutting. Weldon shank to DIN 1835B. Cutting diameter to js12. Shank diameter to h6. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 26 Long RFN-4WL TiCN Coated

Dimensions to DIN 844.