Dormer Jobber Drills for Stainless Steel HSS

Drills up to 4 x diameter. Split point. Point angle: 135. Manufactured to BS328, DIN338.

HSS Jobber Drills For Stainless Steel - Series A108 - Imperial

Sherwood 2 Flute Slot Drills Threaded Shank HSS-Co 5%

Centre cutting, used for profile milling, milling keyways and producing open slots. Surface treatment: bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

Short Series - Inch

Indexa-Seiki Arbor Solid Spacers

Hardened and ground parallel and perpendicular to an accuracy of 0.0002" to ensure accurate running cutters, when used on milling machine arbors. With standard keyways.

Kennedy SDS-Style Fitting Hammer Drill Bits

Kennedy Tungsten carbide tipped SDS masonry drills are suitable for all SDS direct fitting hammer drills. High performance drill bits that withstand extreme heat generation ensuring maximum performance coupled with wear resistance. Manufactured to DIN 8035.

SDS-Plus Hammer Drill Bit

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Kennedy® Milling Cutters Throwaway Micro-Grain Solid Carbide

For high volume production. Compatible with standard automatic locking chucks and spindle adaptors (available on request).

Short Series - Metric

SwissTech Shank Milling Cutters

The latest enhancement of the SwissTech range, these cutters deliver excellent performance when cutting difficult materials, even at high speeds.

Manufactured from premium PM (Powder Metallurgy) tool steel, with an excellent cutting geometry. Designed for strength and rigidity, minimising vibration in high speed cutting applications and providing improved productivity.

These cutters are further enhanced by the SwissTech Peak Power coating, suiting dry cutting applications, having higher oxidization resistance and hot-hardness than conventional TiALN or TiCN coatings, withstanding the high thermal loads associated with high speed cutting applications.

Series 91 2 Flute Fine Slot Drill HSS-E PM Coated

Centre cutting.
Weldon shank to DIN 1835B.
Shank diameter to h6.
Dimensions to DIN 844.

Sherwood Machine Reamers

Sherwood machine reamers are used to produce a close tolerance surface finish by enlarging pre-drilled holes to a finished size. Manufactured from HSS with a 45 bevelled head.

Conform to BS 122 : Part 2 and BS 328 Part 4.

For all technical and dimensional specifications please refer to our catalogue.

Machine Reamers Taper Shank HSS - Metric

Allied Maxcut Indexable Drill Inserts

For a full range of Allied Maxcut Tool holders please refer to our catalogue.

For all technical and dimensional specifications please refer to our catalogue.

Inserts

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.