Indexa-Seiki ER - Single Angle Collets

Collet Dimensions:
Capacity 3.0-26.
(D)41mm x (L)46mm.

ER40

Kennedy® Brazed Tip Turning and Boring Tools

Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40:
Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30:
Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20:
General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates.

For all dimensional and technical specifications please refer to our catalogue.

Cranked Turning Tools

Left Hand. Available in Grades P40, P30 and K20.

Indexa-Seiki ER - Single Angle Collets

Collet Dimensions:
Capacity 3.0-26.
(D)41mm x (L)46mm.

ER40

Sherwood® Solid Carbide Drills

Sherwood Solid Carbide Stub Drills are suitable for drilling into steel, cast steel, cast iron, chilled cast iron, malleable cast iron, non-ferrous materials and abrasive plastic.
Point angle: 118°, helix angle: 30°, tolerance of diameter: h7, tolerance of shank: h6.
Manufactured to Works Standard.

Solid Carbide Stub Drills

Kennedy High Performance Rotary Impact Drill Bits

Tungsten carbide tipped with fully ground flutes. Full flute width, tip seating and specially designed cutting angles. For rapid drilling of concrete, brick, masonry, etc. Suitable for both rotary and rotary-impact use. Manufactured to BS 5621: 1992, ISO 5468 : 1992.

Extra Length

Indexa-Seiki VDI Toolholders

Manufactured to DIN 69880. Suitable for use in NC lathes with VDI fixing disc. Features: All tools are fully carburized and hardened. Surface hardness of 58-60HRc. Tensile strength above 1000N/mm2. Surfaces blued; seat, parallel shank and shoulder ground. Tools can be adjusted in-situ on radial and axial toolholders. Seat shim allows two tool sizes to be used with one toolholder. Ball regulator (bullseye) provides easy coolant control.

Axial

C2 Left Hand

Sandvik Coromant CoroDrill 880 Indexable Drilling Inserts

Guide to Geometry/Feed:
-GM geometry is the basic choice for most materials. Medium feed.
-LM geometry is the best choice for long chipping materials, e.g. low carbon steel and stainless steels. Medium feed, insert with sharp positive edge.
-GR geometry is the high feed choice for steel and cast iron. Insert with strong reinforced edge, suitable for roughing.
-GT geometry is a problem solver for unstable conditions and interrupted cuts. Low to high feed. Good chip control in most materials.

For all technical and dimensional specifications please refer to our catalogue.

CoroDrill 880 Indexable Drilling Insert

Insert size: 880.. 05 03 05H-C (Central insert). Geometry: -LM. Grade H13A: non-ferrous material.

Sherwood Machine Reamers

Left hand spiral flute, right hand cutting. Manufactured to BS 122.

For all dimensional specifications please refer to our catalogue.

Metric

Granlund Size 1 Pilots

Type RS Roller Tol. c9.

When working 'dry' type R roller pilots must be lubricated. Pilots type RS must be combined with holders type AS.

For all technical specifications please refer to our catalogue.

Dormer HSCO Jobber Drills

A901 HSCo PFX Alcrona Top Jobber Drill
High productivity "one-hit" drilling to 6xD
Alcrona Top coating for extended tool life.
Excellent performance across a wide range of materials.
Size Range: 1.5 - 16.0mm, 1/16” - 5/8”