HSS-Co 8% Cobalt Long Series Milling Cutters 2 Flute

Centre cutting, used for profile milling, milling keyways and producing open slots. Surface treatment: bright finish.
Flute type: 30° Helix. Overall dimensions to DIN 844. Plain shank to DIN 1835A.

Long Series

SwissTech 2 Flute Slot Drills Plain Shank Q-Coat Carbide

Centre Cutting. To Manufacturers Standards. Cutting diameter to h10, Shank diameter to h6. 'Q-Coat' Coating has been specifically developed to give carbide cutters the 'edge' when faced with severe machining conditions. Materials up to 66 HRC. Dry cutting. Die and Mould machining. Reduced coolant usage and disposal. Up to 100% longer cutter life. Reduced manufacturing costs. A multi-layer coating capable of operating at higher speed and feed. Excellent oxidisation resistance. High speed machining. Surface hardness 3300HV. Surface coefficient against steel 0.25. Thickness of coating 305um. Maximum working temperature 850. Re-coating service also available.

For all technical and dimensional specifications please refer to our catalogue.

Series 60 Short SDQ-2PS Carbide Q-Coat

Dimensions to DIN 844.

Iscar Parting and Grooving Blades

Iscar's new, single-ended insert for parting with an improved
clamping method, tangentially clamped, single-ended parting system

TAG insert features:
Very rigid clamping in a tangentially oriented pocket.
Enables machining at very high feed rates and provides excellent straightness and surface finish.
Recommended for parting large diameter parts and for interrupted cuts.
Offers a free, unobstructed chip flow, since there is no upper jaw as in the other clamping systems (very important in deep grooving and parting applications).
The combination of tangential clamping and free chip flow results in improved tool and insert lifetime.
Provides a solution to the problem of inserts being pulled out during retraction.

TGFH Part-Off Blade Set

The Iscar TGFH part-off blade set contains:
A double-ended tang-grip blade for parting & grooving.
10x Tag inserts grade IC808.

Grade Description: IC808 (ISO P15-P30, M20-M30, H10-H20, S15-S25)
A hard, fine grain substrate with excellent chipping resistance, combined with a new ?SUMO TEC? TiAlN PVD coating. Provides high wear resistance. Recommended for a very wide range of materials.

Dormer Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series A100

Sherwood Long Series Drills Steam Tempered HSS

General-purpose drills to drill steels with tensile strength up to 1,000N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118, helix angle: normal, web thickness: normal, relief angle: 10-20, tolerance of diameter: h8, tolerance of f11. Manufactured to BS328;Part 1:1986, DIN340RN, ISO494.

For all dimensional specifications please refer to our catalogue.

Series L100 - Metric

Sherwood Gauge Drills HSS Steam Tempered

General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118, helix angle: normal, web thickness: standard, relief angle: 8 - 20, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to ANSI B328, BS 328 and DIN 338.

Number & Letter Gauge Drills:
Gauge drills are still in common use in the U.S. In the past, they were popular elsewhere, but now have been largely discarded in favour of metric sizes. When using a gauge rather than a standard measurement of size the user has to refer to a table of gauge sizes. For example, to drill a hole which is 10 thou (thousandth of an inch .0010) bigger than a 1/8 inch bolt, the user must first work out that 1/8 inch is 125 thou, so the hole size needed is 135 thou, and then must look up in a reference book which gauge drill bit is closest to this diameter - a number 29. Number gauge sizes are similar or equivalent in some respects to, but different from, American wire gauge. Number gauge is usually used from size 80 (the smallest) to size 1 (the largest) followed by letter gauge size A (the smallest) to size Z (the largest). Number gauge is actually defined down to size 97, but these smaller sizes are rarely encountered. It happens that as the technology for making small drill bits and drilling small holes has become more available, metric drills have become the norm.

For all dimensional and technical specifications please refer to our catalogue.

Series J100 - Gauge Sizes

Kennedy Engineers' Hand Files Industrial Quality

Engineers' Hand files have parallel edges, one edge uncut. For flat filing, corner filing and deburring. Multi-purpose and for other work where a 'safe' or uncut edge is needed. Double cut. Available as Smooth Cut, Second Cut and Bastard Cut.

Hand

Smooth Cut

Guhring Long Series Stub Drills HSS TiN Coated

For the drilling of deeper holes and for use with drill bushings. For machining alloyed and unalloyed steel, cast steel, cast iron, German silver and graphite. Type N. Manufactured to DIN340.

For all dimensional specifications please refer to our catalogue.

Series 667 - Metric

Allied Maxcut Series Y Holders

Diameter range: 9.5 to 11.07mm.

For all dimensional specifications please refer to our catalogue.

Flanged Straight Shank

Allied Maxcut Thread Mills

The MaxThread™ threadmill range is manufactured from solid carbide with ground helical flutes and a TiAlN coating as standard. These product have been designed for the low volume/low cost production environment, providing excellent performance at a competitive price. A helical flute design has been maintained across the MaxThread™ range to allow
for maximum production benefits and to negate the need for straight flute thread mills. A comprehensive range of thread forms and technical information further supports the programme.

Features and Benefits:
Helical flute which offers increased strength and rigidity when cutting forces are applied.
TiAlN coated for increased tool life over uncoated tools.
Extensive range of thread forms.
High quality for consistent predictable production.

BSPT Thread Mills

Solid Carbide Threadmills BSW