ISCAR?s new Single-Ended Insert for Parting With an Improved Clamping Method

TAG Insert Features
* Very rigid clamping in a tangentially oriented pocket.
* Enables machining at very high feed rates and provides excellent straightness and surface finish.
* Recommended for parting large diameter parts and for * Offers a free, unobstructed chip flow, since there is no upper jaw as in the other clamping systems (very important in deep grooving and parting applications.
* The combination of tangential clamping and free chip flow results in improved tool and insert life time.
* Provides a solution to the problem of inserts being pulled out during retraction.

The TAG inserts are available with the familiar J- and C-Type chipformers, with neutral and angular frontal cutting edges. The new tools are equipped with a user-friendly clamping and extraction device. The TANG-GRIP family includes square shank tools, blades and inserts in 1.4 - 9.5mm widths in the most advanced IC830 and IC808 SUMO TEC grades. The blades are in standard siuzes which fit ISCAR's standard blocks.

Tang-Grip? TAG N-J Parting & Grooving Inserts

First choice for soft materials, parting of tubes, small diameters and thin-walled parts. Cutting edge with positive rake. General applications on low carbon steel, alloy steel, austinitic stainless steel. Low-to-medium feed.

IC808 Grade Description:
(P15-P30/M20-M30/K20-K40/ S15-S25/N15-N25/H20-H30) SUMO TEC TiAlN PVD coated. A tough submicron substrate. For machining heat resistant alloys, austenitic stainless steel, hard alloys and carbon steel at medium to high cutting speeds. Excellent notch wear and built-up edge resistance.

Kennedy Heavy Duty Drills for Stainless Steel HSS-Co 8%

Heavy-duty drill made of 8% cobalt material with excellent heat resistance. To drill steels with tensile strength up to 1,400 N/mm2, very hard bronze, stainless steels as well as heat and acid resistant steels. Point Angle: 135. Helix angle: Normal. Web thickness: Strengthened. Relief angle: Normal. Tolerance of diameter: h8. Tolerance of shank: f11. Manufacturing Standard: DIN338.

HSCo Heavy Duty Drill For Stainless Steel - Series XT34 - Metric

Sherwood Hand Reamers

Sherwood Taper Pin hand reamers are used to produce a close tolerance surface finish in taper holes to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies.

Manufactured to BS 328 : Part 4 : 1990 and DIN 9A.

For all technical and dimensional specifications please refer to our catalogue.

Taper Pin Hand Reamers - Metric

SwissTech 2 Flute Ball Nose Slot Drills Weldon Shank HSS-Co 8%

Centre cutting. Weldon shank to DIN 1835B. Cutting diameter to e8. Shank diameter to h6. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 11 Short SBN-2WS TiCN Coated

Dimensions to DIN 327.

Sherwood Long Series Drills HSS

General-purpose drills to drill steels with tensile strength up to 1,000N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118, helix angle: normal, web thickness: normal, relief angle: 10-20, tolerance of diameter: h8, tolerance of f11. Manufactured to BS328:Part 1:1986, DIN340RN, ISO494. Bright finish; drills are supplied in the as-ground condition and such tools are used generally in the machining of non-ferrous materials.

For all dimensional specifications please refer to our catalogue.

Series L100 - Metric

Bright finish.

Sherwood Drills Taper Shank HSS

General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345.

For all dimensional specifications please refer to our catalogue.

Series T100 (MT4) - Metric

Indexa-Seiki VDI Toolholders

Manufactured to DIN 69880. Suitable for use in NC lathes with VDI fixing disc. Features: All tools are fully carburised and hardened. Surface hardness of 58 - 60HRC. Tensile strength above 1000N/mm2. Surfaces blued; seat, parallel shank and shoulder ground. Tools can be adjusted in-situ on radial and axial toolholders. Seat shim allows two tool sizes to be used with one toolholder. Ball regulator (bullseye) provides easy coolant control.

Z2 Blanking Plugs

Indexa-Seiki VDI Toolholders

Manufactured to DIN 69880. Suitable for use in NC lathes with VDI fixing disc. Features: All tools are fully carburized and hardened. Surface hardness of 58-60HRc. Tensile strength above 1000N/mm2. Surfaces blued; seat, parallel shank and shoulder ground. Tools can be adjusted in-situ on radial and axial toolholders. Seat shim allows two tool sizes to be used with one toolholder. Ball regulator (bullseye) provides easy coolant control.

Radial

Short, Upside down B3 Right Hand

Sherwood Drill Blanks HSS

Jobber length blank hardened and ground all over. Accurately ground without back taper. Diameter Tolerance: h8. Manufactured to DIN 338.

Series J400

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.