Dormer Jobber Drills TiN Tipped

Dormer's A002 Jobber Drill has a standard helix, it is right hand and has wider flutes for efficient chip removal. 118 point geometry. TiN coated on the tip for high wear resistance, lower friction and allows increased cutting speeds. Suitable for general-purpose drilling.
The Dormer A002 Jobber drill delivers the following features and benefits:
Improved web design optimises strength and rigidity and increases feed capability
Ground wide flutes allow for efficient chip evacuation
Optimised throughout the helix range for greater rigidity
Bright body improves application on ductile materials
Titanium Nitride coating focused on the working surfaces to resist flank and crater wear, and to provide low friction and increased performance
Special Dormer P.S. Point increases ease of penetration, improves hole size and provides accurate centering
General purpose engineering drills
Manufactured to BS328:Part 1:1986.

Series A002

Mitsubishi Indexable Milling Inserts

Mitsubishi APX4000 Milling inserts have been developed using advanced simulation technology to produce a new 15mm insert is suitable for larger depths of cut. The new insert is also thicker and therefore ideal for high load machining they are also:
Efficient when machining on low rigidity machines or work pieces and they are ideal for thin wall or extended reach applications.
They have efficient heat disposal and chip control, heat generated during cutting has been reduced due to the APX?s special geometry.
Ideal chip shape formed by the insert for easy disposal.

AOMT Indexable Milling Insert

Mitsubishi grade description: VP15TF (P15-P35/M15-M35/K15-K30) PVD ''Miracle'' Coated Milling/Drilling Grade. Offers increased heat resistance and adhesion strength. For all Steels, Cast Irons and some Stainless Steel

Sherwood Straight Shank Parallel Hand Reamers

Used to produce a close tolerance surface finish by hand in almost any environment i.e. on site or in a workshop. Manufactured to BS 328 : Part 4 : 1990 and DIN 206B.

Spiral Flute Parallel Hand Reamers - Metric

For all dimensional specifications please refer to our catalogue.

Dormer Taps

Dormer MTT-X Series taps are manufactured from HSS-X1 Steel with a Bright finish, they are right Hand Cutting.

Manufactured to ISO 529
Spiral Flute for threading blind holes.
Taper lead to DIN form C.
Tapping tolerance to 6H.
Max Depth 2.5 x D.
Helix angle 48.

For all technical and dimensional specifications please refer to our catalogue.

Dormer HSCo Stub Drills

Excellent for drilling higher tensile, tougher materials
135° split point for improved precision and finish (over 1.5mm).
Manufactured to DIN1897.

HSCo Stub Drills - Series A117 - Metric

Sherwood 2 Flute Slot Drills Threaded Shank HSS-Co 5%

Centre cutting, used for profile milling, milling keyways and producing open slots. Surface treatment: bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

Short Series - Metric

Allied Maxcut Series 1 and 1.5 Holders

Diameter range: 17.53 to 24.38mm.

For all dimensional specifications please refer to our catalogue.

Flanged Straight Shank

Kennedy High Performance Rotary Impact Drill Bits

Tungsten carbide tipped with fully ground flutes. Full flute width, tip seating and specially designed cutting angles. For rapid drilling of concrete, brick, masonry, etc. Suitable for both rotary and rotary-impact use. Manufactured to BS 5621: 1992, ISO 5468 : 1992.

Standard Length

Mitsubishi Grooving & Parting Inserts

Grade Description: VP10RT is the first recommendation for turning difficult-to-cut materials with a good balance of wear and fracture resistance.

GY Series Grooving & Parting Inserts

GY Inserts To Suit External Face and Internal Grooving Holders.

A full range of insert widths from 2mm to 6.35mm are available on request.

SwissTech Production Drills Solid Carbide Q-Coat

SwissTech? Q-Coated carbide drills are for drilling into general steel, cast steel, cast iron, chilled cast iron, malleable cast iron, non-ferrous heavy and light metal, and abrasive plastic. They are self-centering with a point angle: 140.

Tolerance of diameter: m7.
tolerance of shank: h6.
Manufactured to DIN 6537.

Solid Carbide Drill 5 x D - Metric