Granlund HSS Size 1 Counterbores

Type W. HSS. Tolerence P8.

Counterbores W with a diameter of 50mm and larger are all made with a driving lip. These sizes should be used in the appropriate type M toolholder.

For further specifications please refer to our catalogue.

Allied Maxcut Series Y Inserts

For all dimensional specifications please refer to our catalogue.

GEN2 T-A HSS Super Cobalt AM200 Coated

Starrett Bandsaw Blades

Made from carbon steel with a flexible back, Duratec™ SFB is ideal for economical cutting on easy-to-machine ferrous or non-ferrous metal and wood.
Features: Flexible carbon steel back. Wide range of widths, thickness and pitches.
Benefits: Blades can be run at higher band speeds than standard bi metal blades.
Economical general purpose cutting. Ideal for both contour & straight cutting.
Suitable for light vertical and horizontal machines.
Applications: Wood, plastics.
Non-ferrous foundry materials.
Low alloy and non-ferrous metals.
Furniture, composition board.

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

PSC and PSCa (adjustable) Collets for Plain Shank Cutters

Tru-Loc Collets are available for plain shank cutters in two different styles, PSC non adjustable and PSCa - Collets with an adjustable back-stop screw to allow more accurate & consistent cutter replacement.

For all dimensional specifications please refer to our catalogue.

PSC(a) Type

Walter Titex Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series A1211

Kennedy Precision Hand Files Needle Pattern (Round Handle)

Available in 14cm and 16cm lengths and a complete range of shapes. Manufactured to BS 498:1990.

Round

Available in Cut 0, 2 or 4.

Sherwood Die Nuts

Sherwood ground thread die nuts are suitable for repairing damaged or crossed threads and clearing swarf from threads. When using a die nut (on an existing thread) it is not necessary to apply the same level of precise initial alignment required to form a new thread (i.e. with a die) as the nut will follow the existing threads. They are supplied as hexagon drive allowing them to be turned by a standard spanner or adjustable wrench without the need for a special stock.

Conform to: ISO 529

For all technical and dimensional specifications please refer to our catalogue.

Die Nuts (British Standard Pipe Fine) Ground Thread HSS

Manufactured to: BS1127
Thread Form to: BS21

Kennametal Indexable Turning Inserts

Grade Description: KC850 grade is equivalent to the following grades M25-M45, P25-P45. A tri-phase coating on an extra strong, cobalt-enriched substrate makes this Kennametal CNMG insert suitable for general purpose machining of many work piece materials. With the advent of higher machine tool spindle speeds, today it finds its best application in heavy cutting of low, medium, and high carbon steels, as well as medium hardness alloy and tool steels. Excellent thermal and mechanical shock resistance makes grade KC850 ideally suited for difficult applications with interruptions.

For all technical specifications and tool holders please refer to our catalogue.

Kennedy® Ball Nosed Slot Drills Plain Shank Carbide Micrograin

For optimum performance and maximum swarf removal when plunging, slotting and routing in most materials including brass, aluminium, non ferrous and other soft materials. Manufactured to USCTi Standards.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 2 Flute - Metric