DNMG

Suitable for External/Internal Toolholders.

Guhring Drills Taper Shank HSS-Co 5%

High heat resistant drill for drilling alloyed and unalloyed steels and castings with a tensile strength over 800N/mm2. Especially suitable for hot and cold rolled steels as well as case hardening and heat treatable steels. Manufactured to Type N DIN345.

For all dimensional specifications please refer to our catalogue.

Series 345 (MT2) - Metric

HSS Plain Shank Dovetail Cutters (Single Angle Cutters)

Bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

Long Series Type 5331T - Metric

For all dimensional and technical specifications please refer to our catalogue.

Sherwood 2 Flute Slot Drills Threaded Shank HSS

Used for milling keyways and slots in one unit. Bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

For all dimensional and technical specifications please refer to our catalogue.

Short Series S210T - Metric

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Kennedy Toolbits & Parting-Off Blades

Cut faster, 'stand up' longer and reduce costs. Square and rectangular toolbits supplied with 10 bevelled ends. Parting off blades supplied with 2 side taper, 15 bevel (top and bottom).

5% Cobalt Square Metric

Sherwood Taps

Sherwood HSS Taps are the general purpose option for thread cutting in most materials including steel, some stainless steels, cast irons and non-ferrous materials such as Aluminium, Brass and many others.

Manufactured with precision ground flutes for producing accurate thread forms, Sherwood Taps are available in all the popular thread forms and as straight Flute `Hand` Taps in 3 leads, Fluteless, Spiral Flute, or Spiral Point Machine Taps and also Long Series.

Sherwood Tap dimensions conform to ISO529 apart from NPT Forms which conform to ANSI 94.9. Straight Flute and Fluteless Taps are manufactured with a standard Bright Finish whereas the Machine Taps have an Oxidised Finish for best results dissipating the heat build-up associated with these applications.

Thread Forms are Class 2 medium fit tolerance.

For all technical and dimensional specifications please refer to our catalogue.

Tap Set BSPF (British Standard Pipe Fine) Straight Flute Ground Thread HSS

Each set of Sherwood taps contain one taper, second and plug lead tap:

Sherwood HSS Taper Taps are used to start cutting the thread. They are tapered back from the end 6 to 10 threads before a fully threaded diameter is reached. This allows the tap to be positioned easily and correctly before it starts to cut the thread.

The Second Tap is used after the taper tap has cut threads into the hole as far as possible. It tapers back 3 or 4 threads before full thread diameter is reached.

The Plug Tap cuts threads to the bottom of a blind hole. It is only necessary to use the full set of taps when a blind hole is to be tapped.

CCMT

JC215V (ISO P10-P40 K25-K40) On the wear-resistance and tougher base material, multi-layer coating are adopted. This grade shows twice the tool life as conventional grade. Medium to high speed cutting for steels and medium speed cutting for cast iron.
FT - Excellent swarf control can be obtained at small depth of cut and low feed rate. Excellent finish to work-surface is achievable. This fine finishing chipbreaker offers an optimum for high-speed cutting when used with Cermet Grade inserts.

Sherwood HSS Plain Shank Corner Rounding Cutters

Designed to produce convex corner radii. For milling structural, carburising and heat treated steel up to 900N/mm2.
Manufactured to works standards.
5° RH Flutes.
Bright finish, straight helix.
Radii tolerance: ± 0.005”.

Metric

HSS-Co. 8% Plain Shank Milling Cutter 4 Flute

Centre cutting, used for profile milling, milling keyways and producing open slots.
Bright finish. Flute type: 30° helix.
Overall dimensions to DIN 844.
Plain shank to DIN 1835A.

Metric Tolerances
Nominal Dia. Limits of Tolerance
Up to 38mm 0.0630 -0.0130
Above 38mm 0.1250 -0.0000

Regular Length