Sherwood Straight Shank Parallel Hand Reamers

Used to produce a close tolerance surface finish by hand in almost any environment i.e. on site or in a workshop. Manufactured to BS 328 : Part 4 : 1990 and DIN 206B.

Spiral Flute Parallel Hand Reamers - Metric

For all dimensional specifications please refer to our catalogue.

Sherwood Extra Length Drills Steam Tempered HSS

General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118, helix angle: normal, web thickness: standard, relief angle: 10-20, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS 328 : Part 1 : 1986.

For all dimensional specifications please refer to our catalogue.

Series E100 - Inch Sizes

Dijet Carbide End Mills

Dijet AL-SEELS series End Mills are for profiling & Slotting in Aluminium and Alloys

AL-SEEL-2 Long Series Carbide End Mill

Dijet AL-SEELS series Carbide end mill specification:
Sharp corner.
Helix angle 45.
2 flute.
Centre cutting.
Regular cutting edge.
Shank cutting diameter to 0.04-0.0
Weldon shank to DIN 1835B.

Dormer Stub Drills

A921
High productivity "one-hit" drilling to 3xD. Excellent performance across a wide range of materials. Parabolic flute design promotes constant chip flow. Alcrona Top coating for extended tool life
Size Range: 2.5-16.0mm. Manufactured to BS 323, DIN1897, ansi.

A921 HSCO Stub Drills

A9210
Excellent for: Carbon/alloy steels, stainless and cast iron
Good for: Titanium, nickel and copper

Taylor & Jones Expanding (Re-grindable) Machine Reamers Taper Shank HSS

Type 109M - Regrindable
Used to produce close tolerance surfaces and can be re-ground to give a greatly extended tool life. Ideal for production reaming of intermediate diameters. Manufactured to BS 328-4. Inch limits of Tolarance (to H7).

For all dimensional specifications please refer to our catalogue.

Expanding Machine Reamers - Inch

Carbide Tipped Holesaws

Kennedy carbide tipped holesaws last up to 10 times longer than standard hole saws and resist wear and heat caused by friction much better than traditional holesaws, making them the best choice for cutting tough material such as tile, stainless steel.

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

Holesaws Carbide Tipped

Indexa-Seiki ER Spanners & Locknuts

Suitable for all collet chucks including straight shank.

Sherwood® Solid Carbide Drills

Sherwood Solid Carbide Stub Drills are suitable for drilling into steel, cast steel, cast iron, chilled cast iron, malleable cast iron, non-ferrous materials and abrasive plastic.
Point angle: 118°, helix angle: 30°, tolerance of diameter: h7, tolerance of shank: h6.
Manufactured to Works Standard.

Solid Carbide Stub Drills

Kennedy® Ball Nosed Slot Drills Plain Shank Carbide Micrograin

For maximum strength when milling harder materials where rapid swarf removal is not needed. 4 flute milling cutters have one of the strongest tooth structures available in solid cutters. Centre cutting as standard. Manufactured to ANSI Standards.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 4 Flute - Inch

For maximum strength when milling harder materials where rapid swarf removal is not needed. 4 flute milling cutters have one of the strongest tooth structures available in solid cutters. Centre cutting as standard. Manufactured to Ansi Standards.
Inch Tolerances
Nominal Limits Of Tolerance
Diameter High Low
1/16" - 1/4" 0.000 -0.002
17/64" - 1" 0.000 -0.003
Metric Tolerances
Nominal Limits Of Tolerance
Diameter High Low
1 - 6 0.000 -0.050
7 - 25 0.000 -0.080

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.