Dormer Stub Drills

A920 - HSCo PFX Stub Drills
High productivity "one-hit" drilling to 3xD. Excellent performance across a wide range of materials. Parabolic flute design promotes constant chip flow.Size Range: 1.0-20.0mm. Manufactured to BS 323, DIN1897, ansi.

A920 - HSCo PFX Stub Drills - Inch

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Kennedy® Brazed Tip Turning and Boring Tools

Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40:
Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30:
Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20:
General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates.

For all dimensional and technical specifications please refer to our catalogue.

Brazed Tip Cranked Turning & Facing Tools

Left Hand. Available in Grades P40, P30 and K20.

Kennedy Holesaws

Kennedy holesaw pilot drills are for use with Kennedy holesaw arbors they are manufactured from high speed steel and have ground flutes. Using a pilot drill with a holesaw and arbor ensures the hole is accurately cut exactly where you require it.

For the full range of Kennedy hole saws and arbors please refer to our catalogue.

K14D Pilot Drill for K4 Arbors

Indexa-Seiki ER - Collet Chucks

The Indexa-Seiki ER Collet chuck is manufactured as part of Europe's most popular collet system. The collapsing collet design can be used for a range of diameters and maintains concentricity for drilling and milling. Long reach options are also available to give access into deep recesses. Balanced to 12,000rpm. Max Tir 0.010mm. (BT BT-MAS 403)



To BT-MAS 403

Dormer Solid Carbide Drills

The new Dormer MP-X range of multi-application carbide drills are cost effective, high performance drills that offer high productivity and supreme value for money. A wide range of materials can be machined using a minimum number of drills, to reduce stock-holding and associated costs.

MP-X Solid Carbide Drills

Dormer MP-X solid carbide drills deliver the following benefits and features:

Benefits
? Exceptional value with no compromise on quality.
? High productivity.
? Excellent hole quality.
? Availability.
? Reduced tooling costs.

Material
Micro-grain carbide for an excellent combination of hardness and toughness, resulting in high wear resistance and longer tool life.

Coating
Multi-layer titanium aluminum nitride (TiAlN) coating gives:
? Improved stability of cutting edges.
? Outstanding wear protection.
? High hardness properties.
? High toughness and oxidation stability
? Longer tool life and higher productivity.

Flute Geometry
Strong web design gives excellent crosssectional strength and facilitates chip evacuation.

Point Geometry
140 point angle with good centring capabilities and low thrust force design, suited to multiapplication drilling.

Multi-Application
Multi-application drilling across a wide range of materials, including:
? Carbon and alloy steels.
? Stainless steels.
? Cast iron.
? Aluminium.
? Magnesium alloys.
? Copper.

Suitable for Regrinding
The quality of design will allow consistently high levels of performance and tool life after the product is reconditioned, providing further cost reduction benefits.

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Sherwood Die Nuts

Sherwood ground thread die nuts are suitable for repairing damaged or crossed threads and clearing swarf from threads. When using a die nut (on an existing thread) it is not necessary to apply the same level of precise initial alignment required to form a new thread (i.e. with a die) as the nut will follow the existing threads. They are supplied as hexagon drive allowing them to be turned by a standard spanner or adjustable wrench without the need for a special stock.

Conform to: ISO 529

For all technical and dimensional specifications please refer to our catalogue.

Die Nuts BSW (British Standard Whitworth) Ground Thread HSS

Manufactured to: BS1127
Thread form to: BS84

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Dormer Metric Coarse HSS Ground Thread Taps

Series E500. Comply with IS529.

Second Tap (Straight Flute)