SwissTech Heavy Duty Stub Drills HSS-Co Cobalt

Heavy duty drill made of high quality cobalt material with excellent heat resistance. For drilling steels up to 1,400N/mm2, stainless steel, heat resistant steels and bronze. Ideally suited for volume production on automatics. Point angle: 135. Helix angle: Normal. Web thickness: Strengthened. Tolerance of diameter: h8, Tolerance of shank: f11. Manufactured to DIN1897RN.

Series 2010

Iscar Turning Inserts

IC3028 Grade description: (ISO P25-P45 M15-M35 S20-S30).
A TiN/TiCN PVD toughest coated grade. Used for turning stainless steel and high temperature alloys at low to medium cutting speeds. Used for interrupted cuts and very heavy turning operations.

SNMG

Kennedy High Performance Rotary Impact Drill Bits

Tungsten carbide tipped with fully ground flutes. Full flute width, tip seating and specially designed cutting angles. For rapid drilling of concrete, brick, masonry, etc. Suitable for both rotary and rotary-impact use. Manufactured to BS 5621: 1992, ISO 5468 : 1992.

Medium Length

Allied Maxcut Series 4 Holders

Diameter range: 46.99 to 65.28mm.

For all dimensional specifications please refer to our catalogue.

Flanged Straight Shank

Kennedy Endmills

Kennedy KC3 throwaway 3* flute endmills are manufactured HSS-Co 5% making them much tougher than HSS. This means that Kennedy endmills can be used at higher speeds and feeds which in turn gives greater productivity.

Kennedy KC3 endmills are available uncoated, TiN coated and TiCN coated.

TiN (Titanium nitride) provides a surface hardness in the region of 2300HV which offers improved wear resistance, tool life and productivity.

TiCN (Titanium Carbonitride) gives a surface hardness in the region of 3000-3500 HV, excellent wear resistance and good heat resistance. This coating is used for the same things as TiN but also for hard steels, stainless, cast iron, brass & bronze.

For all technical and dimensional specifications please refer to our catalogue.

*Except: 1mm cutters, 2mm and 1/16" ball nose cutters, all of which have two flutes.

KC3 Endmill Short Series 3* Flute Throwaway Cutter Weldon Shank HSS-Co 5% TiN Coated- Metric

Sherwood Extra Length Drills Steam Tempered HSS

General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118, helix angle: normal, web thickness: standard, relief angle: 10-20, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS 328 : Part 1 : 1986.

For all dimensional specifications please refer to our catalogue.

Series E100 - Metric

SwissTech 2 Flute Ball Nosed Slot Drills Threaded Shank HSS-Co 8%

Centre cutting. Threaded shank to DIN 1835B. Cutting diameter to e8. Shank diameter to h6. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 39 Short SBH-2TS HSS-Co 8%

Dimensions to DIN 327.

SS-Co 5% 3 Flute Piloted Countersinks

For the production of high precision concentrically centred countersinks in most metals where pilot holes have been pre-drilled.
Shank diameter: 3/16”.

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Sherwood Jobber Drills Bright Finish HSS

General-purpose drills for steel, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle 118, helix angle: normal, web thickness: standard, relief angle: 10-20, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS328/DIN338RN. Bright finish: drills with a bright finish are supplied in the as-ground condition and such tools are used generally in the machining of non-ferrous materials.

Series J100 - Metric - Bright Finish