Granlund Size 1 Pilots

Type R Roller. c9.

When working ?dry? type R roller pilots must be lubricated. Pilots type RS must be combined with holders type AS.

For all technical specifications please refer to our catalogue.

Kennedy Drills for Stainless Steel HSS-Co 8%

Deep hole drill with high heat resistance to drill non alloyed and alloyed steels as well as long chipping materials with tensile strength up to 1,300N/mm2. Special point design with web thinning form S optimised chip breaking and reduced feed force and torque. Ample chip space enables drilling over five times diameter deep without pecking. Point angle: 130. Helix angle: High. Web thickness: Strengthened. Relief angle: Normal. Tolerance of diameter: h8. Tolerance of shank: f11. Manufactured to DIN338.

Drills for Stainless Steel HSS-Co 8% - Inch

Walton Replacement Fingers for 3 Flute Extractors

Thoroughly remove all chips of the broken tap. insert the extractor fingers into the flutes of the broken tap, pushing them gently but firmly into position. Push the holder down until it touches the broken tap. slide the sleeve down until it touches the work. Apply a tap wrench to the square end of the holder. Twist forward and backward a few times to loosen, then back out the broken tap.



Supplied Individually.

SwissTech 2 Flute Slot Drills Plain Shank Q-Coat Carbide

Centre Cutting. To Manufacturers Standards. Cutting diameter to h10, Shank diameter to h6. 'Q-Coat' Coating has been specifically developed to give carbide cutters the 'edge' when faced with severe machining conditions. Materials up to 66 HRC. Dry cutting. Die and Mould machining. Reduced coolant usage and disposal. Up to 100% longer cutter life. Reduced manufacturing costs. A multi-layer coating capable of operating at higher speed and feed. Excellent oxidisation resistance. High speed machining. Surface hardness 3300HV. Surface coefficient against steel 0.25. Thickness of coating 305um. Maximum working temperature 850. Re-coating service also available.

For all technical and dimensional specifications please refer to our catalogue.

Series 62 Long SDQ-2PL Carbide Q-Coat

Dimensions to DIN 844.

Eclipse Hacksaw Blades HSS

General purpose edge hardened blades, virtually unbreakable. Provides flexibility and safety but less wear resistance than an all hard or bi-metal blades.

Sherwood Taps

Sherwood HSS Taps are the general purpose option for thread cutting in most materials including steel, some stainless steels, cast irons and non-ferrous materials such as Aluminium, Brass and many others.

Manufactured with precision ground flutes for producing accurate thread forms, Sherwood Taps are available in all the popular thread forms and as straight Flute `Hand` Taps in 3 leads, Fluteless, Spiral Flute, or Spiral Point Machine Taps and also Long Series.

Sherwood Tap dimensions conform to ISO529 apart from NPT Forms which conform to ANSI 94.9. Straight Flute and Fluteless Taps are manufactured with a standard Bright Finish whereas the Machine Taps have an Oxidised Finish for best results dissipating the heat build-up associated with these applications.

Thread Forms are Class 2 medium fit tolerance.

For all technical and dimensional specifications please refer to our catalogue.

Plug Taps Metric Coarse Ground Thread HSS

The Sherwood Plug tap is used last after the Taper and Second tap have been used, when threading blind holes it cuts threads to the bottom of the hole.

Sherwood Extra Length Drills Taper Shank HSS

General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium, alloy and graphite. Point angle 118, helix angle: normal, web thickness: standard, relief angle 8-20, tolerance of diameter: h8. Point angle to BS328 PTI 1986.

For all dimensional specifications please refer to our catalogue.

1 Morse Taper - Inch

M42 Bi-Metal Bandsaw Blades

Starrett Powerband Gladiator M42 is the ultimate competitor in bi-metal bandsaw blades, providing a universal solution with optimum efficiency in large production cutting operations. A high speed steel M42 cutting edge, incorporating a new tooth design with a positive rake angle and variable pitch, combine to give Powerband Gladiator? M42 the utmost in cutting performance and cost effectiveness.

Powerband Gladiator Welded Loops

Recommended applications for Starrett Powerband Gladiator M42 bandsaw blades:
- High production cutting, full range of steels from mild to stainless up to 45 HRC, nickel-based and non-ferrous alloys
Features and Benefits:
- New tooth design features triple-tempered
- M42 high speed steel with 8% cobalt
- Rockwell C67-69
- Up to 12 positive rake angle
- Fatigue resistant alloy steel backing strip
- High wear and heat resistance
- Variable pitch teeth reduce vibration for smooth, quick cutting
- Easy penetration, excellent chip clearance, reduced noise levels
- Improved surface finish
- Faster, straighter cuts

Sherwood Taps

Sherwood HSS Taps are the general purpose option for thread cutting in most materials including steel, some stainless steels, cast irons and non-ferrous materials such as Aluminium, Brass and many others.

Manufactured with precision ground flutes for producing accurate thread forms, Sherwood Taps are available in all the popular thread forms and as straight Flute `Hand` Taps in 3 leads, Fluteless, Spiral Flute, or Spiral Point Machine Taps and also Long Series.

Sherwood Tap dimensions conform to ISO529 apart from NPT Forms which conform to ANSI 94.9. Straight Flute and Fluteless Taps are manufactured with a standard Bright Finish whereas the Machine Taps have an Oxidised Finish for best results dissipating the heat build-up associated with these applications.

Thread Forms are Class 2 medium fit tolerance.

For all technical and dimensional specifications please refer to our catalogue.

Tap Set Metric Fine Straight Flute Ground Thread HSS

Sherwood HSS taper taps are used to start cutting the thread they is tapered back from the end 6 to 10 threads before a fully threaded diameter is reached this allows the tap to be positioned easily and correctly before it starts to cut the thread.

The Second tap is used after the taper tap has cut threads into the hole as far as possible. It tapers back 3 or 4 threads before full thread diameter is reached.

The Plug tap cuts threads to the bottom of a blind hole. It is only necessary to use the full set of taps when a blind hole is to be tapped.

Each set of Sherwood taps contain one taper, second and plug lead tap.

Sherwood Dies

Sherwood UNC (Unified Coarse) HSS dies are used in diestocks to produce external screw threads.

Thread form to: BS 1580

For all technical and dimensional specifications please refer to our catalogue.

Dies UNC (Unified Coarse) Ground Thread HSS