Kennedy SDS-Style Fitting Hammer Drill Bits

Kennedy Tungsten carbide tipped SDS masonry drills are suitable for all SDS direct fitting hammer drills. High performance drill bits that withstand extreme heat generation ensuring maximum performance coupled with wear resistance. Manufactured to DIN 8035.

SDS-Plus Hammer Drill Bit

Collets

For use with Autolock chucks to hold shank milling cutters.

Guhring GT100 Long Series Drills HSS

A robust drill for drilling deeper holes in difficult conditions when swarf congestion prevents an adequate flow of coolant from reaching the drill point. For use in steel and cast iron having a hardness of up to 1000N/mm2. Manufactured to DIN340.

For all dimensional specifications please refer to our catalogue.

Series 535 - Metric

3 Flute - Straight Shank

Manufactured from M35 HSS and used for the deburring and chamfering of most metals and plastics.
Manufactured to BS 328 : Part 5 : 1983.
Inclusive angle 82°.

Sherwood Drills Taper Shank HSS

General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345.

For all dimensional specifications please refer to our catalogue.

Series T100 (MT1) - Metric

Swisstech Fine Pitch Ripper Cutters Weldon Shank HSS-E PM TiALN Coated

Centre cutting. Weldon shank to DIN 1835B. Cutting diameter to js12. Shank diameter to h6. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 26 Long RFN-4WL TiCN Coated

Dimensions to DIN 844.

Sherwood Dies

Sherwood dies are for use in die stocks to cut external screw threads on metal rod, the split in the die allows the adjusting screws of the diestock to compress or expand the die to accommodate for slight variations in size of the material being threaded or die sharpness. Sherwood dies are available as Metric Fine, Metric Coarse, UNF, UNC, BA, BSF, BSW, BSPT, BSPF, NPT cutting threads all the dies are manufactured from HSS with precision ground threads to the applicable standard.

For all technical and dimensional specifications please refer to our catalogue.

Dies Metric Fine HSS

HSS Plain Shank Dovetail Cutters (Single Angle Cutters)

Bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

45° Corner Angle - Inch (Form C)

For all dimensional and technical specifications please refer to our catalogue.

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Granlund Carbide Size 1 Counterbores

Type WHV. For Carbide inserts. Tolerance plus/minus 0.1.

The WHV Rotatip counterbore should always be combined with type R or RS roller pilots. The shank of the holder must not be smaller than MT3.

For further specifications please refer to our catalogue.