Sherwood 2 Flute Ball Nose Slot Drills Threaded Shank HSS

Used for diesinking, slot milling and profile milling. Bright finish. Flute type: 30° helix. Manufactured to BS 122 : Part 4 : 1980.

For all dimensional and technical specifications please refer to our catalogue.

Short Series Type B210T - Inch

Sandvik Coromant CoroDrill 880 Drill Bodies

Stronger drill body with new surface treatment can withstand higher feeds. Wiper geometry for best surface finish. Optimized chip channels for accelerated chip evacuation. Easy identification due to laser marking with drill-, insert- and screw codes on the drill shank.

For all dimensional/technical specifications and for a full range of available Inserts, please refer to our catalogue.

Cylindrical shank - flat according to ISO 9766.

CoroDrill 880 Drill Bodies

Kennedy High Performance Rotary Impact Drill Bits

Tungsten carbide tipped with fully ground flutes. Full flute width, tip seating and specially designed cutting angles. For rapid drilling of concrete, brick, masonry, etc. Suitable for both rotary and rotary-impact use. Manufactured to BS 5621: 1992, ISO 5468 : 1992.

Extra Length

Dormer 2 Flute Slot Drills Threaded Shank HSS

Used for milling keyways and slots in one unit. Bright finish. Flute type: 30 helix. Manufactured to BS 122: Part 4: 1980.
Material:
XS1 HSS powder metallurgy steel. This provides a finer and more consistent grain structure than HSCo resulting in a tougher product able to more easily withstand the shock load and intermittent cutting associated with milling operations. Tool life and wear resistance, exceeds standard HSS and is comparable to HSCo cutters. Superior edge strength and rigidity, resulting in improved surface finish and slot consistency equal to and in some cases better than HSCo. A productivity increase of around 40% over existing HSS cutters. Flute and overall lengths: to BS122/4.
Finish: bronze finish: provides a uniform structure and hardness at the tool surface, whilst also aiding tool identification.

For all dimensional and technical information please refer to our catalogue.

Short Series C191 - Inch

Iscar Helido Indexable Endmills and Facemills

The new HELIDO H490 ANKX rectangular inserts have 4 helical right-hand positive cutting edges. They were designed in cutting edge lengths of 9, 12 and 17 mm. Insert construction is very thick and strong; clamped into a dovetail inclined pocket which provides a very rigid clamping and has a wiper which leaves an excellent surface finish.

Due to its strong construction, unique chip deflector with positive cutting angles and excellent grade combinations, this new family features high durability, low cutting forces and long tool life. Our most advanced SUMO TEC grades ensure excellent performance and reliability.

The new HELIDO tools can be used for machining steel, stainless steel and cast iron at very high machining parameters. HELIDO"s state-of-the-art of milling insert design, enables excellent performance and extremely high productivity.

H490 - A new family of double-sided inserts with 4 helical cutting edges.

For further specification on this product please see refer to our catalogue page.

H490 F90AX...-09 Indexable Face Mills

Face Mills with double-sided inserts, diameter range 32-63mm.

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

SwissTech Heavy Duty Drills HSS-Co 8% Cobalt TiN Coated

Heavy-duty drill used to drill steels with a tensile strength up to 1,400 N/mm2. Stainless steels, heat and acid resistant steels and phosphor bronze. TiN coating provides longer tool life. Point angle: 135. Helix angle: Normal. Web thickness: Strengthened. Relief angle: Normal. Tolerance of diameter: h8. Supply unit. All diameters - 1 pce. Manufactured to DIN338RN.

Series 1033 - Metric

VNMG Indexable Turning Inserts

QX530 (ISO P20-P40 M20-M30) Coated. Turning grade for Steels, Cast Steels and Stainless Steels. A good general purpose Steel grade for roughing.



Suitable for External Toolholders

Sherwood Extra Length Drills Taper Shank HSS

General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium, alloy and graphite. Point angle 118, helix angle: normal, web thickness: standard, relief angle 8-20, tolerance of diameter: h8. Point angle to BS328 PTI 1986.

For all dimensional specifications please refer to our catalogue.

1 Morse Taper - Inch

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.