Indexa-Seiki SL - Sidelock Adaptors

For Weldon shank cutters, adaptors and tapping chucks. Manufactured to stringent quality standards.

Short Length

To DIN69871/A

Kennedy Toolbits & Parting-Off Blades

Cut faster, 'stand up' longer and reduce costs. Square and rectangular toolbits supplied with 10 bevelled ends. Parting off blades supplied with 2 side taper, 15 bevel (top and bottom).

5% Cobalt Square Inch

Sherwood Hand Reamers

Sherwood Taper Pin hand reamers are used to produce a close tolerance surface finish in taper holes to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies.

Manufactured to BS 328 : Part 4 : 1990 and DIN 9A.

For all technical and dimensional specifications please refer to our catalogue.

Taper Pin Hand Reamers - Inch

SwissTech 3 Flute 37 Coarse Pitch High Helix Roughing Endmills for Aluminium HSS-Co 8%

Centre cutting. Weldon shank to DIN 1835B. Shank diameter to h6. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 20 Regular RHN-3WR TiN

Dimensions to DIN 844.

Walter Titex Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series A1211

CNMG

Suitable for External/Internal Toolholders

SwissTech 4 & 6 Flute End Mills Threaded Shank HSS-Co 8%

Centre cutting. Weldon shank to DIN 1835B.
Shank cutting diameter to plus0.04 -0.0.

Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 37 Long EMN-4TL TiCN Coated

Dimensions to DIN 844.

Guhring Production Jobber Drills HSS-Co 5%

Rigid, high-heat resistant drill with large helix angle of 35. Suited for titanium and titanium alloys, stainless steels and heat resisting austenitic steels. Limited suitability for special alloys such as hastaloy, inconel, nimonic etc. Manufactured to DIN338.

Series 605 - Metric

HSS Plain Shank Dovetail Cutters (Single Angle Cutters)

Bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

Long Series Type 5331T - Metric

For all dimensional and technical specifications please refer to our catalogue.

Indexable Toolholder & Insert Sets

Tool supplied complete with 10 Carbide inserts, in a choice of P Grade for steels and general use, or K Grade for cast iron and non-ferrous applications. Inserts supplied will vary according to availability.

PCLN R/L

95° approach. Uses CN_A & CN_G Inserts. For toolholder details see IND-106-1980K/-2000K/-2040K/-2060K.