Dormer Machine Taps

MTT-X taps are manufactured from premium quality vanadium powder steel, branded HSS-XS1, for an unbeatable combination of toughness, edge strength and wear resistance. This winning combination enables them to withstand the stresses of threading in tough materials. Special gold finish with bright flutes/thread, or steam tempering (blue) guarantee a smooth cutting action with less build-up on the cutting edge.

For all dimensional specifications please refer to our catalogue.

ISO Metric: E000 Spiral Point (Gold Coated)

For through holes. Taper lead to DIN form B. Tapping tolerances to 6H. Max depth 2.5 x D.

Sherwood® Slitting Saw Blades

Sherwood® HSS slitting saws are used for cutting metal, these small diameter saws are hollow ground to give the clearance necessary for deep cutting.

Sizes up to 1" diameter do not have key ways.

For all technical and dimensional specifications please refer to our catalogue.

Slitting Saw Small Diameter HSS

Kennedy Heavy Duty Drills for Stainless Steel HSS-Co 8%

Heavy-duty drill made of 8% cobalt material with excellent heat resistance. To drill steels with tensile strength up to 1,400 N/mm2, very hard bronze, stainless steels as well as heat and acid resistant steels. Point Angle: 135. Helix angle: Normal. Web thickness: Strengthened. Relief angle: Normal. Tolerance of diameter: h8. Tolerance of shank: f11. Manufacturing Standard: DIN338.

HSCo Heavy Duty Drill For Stainless Steel - Series XT34 - Metric

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Allied Maxcut Series 2 and 2.5 Holders

Diameter range: 24.41 to 35.05mm.

For all dimensional specifications please refer to our catalogue.

Taper Shank

EX31 DIN 2184-1 Spiral Flute UNF Taps

Steam Tempered Finish

Sherwood 2 Flute Slot Drills Threaded Shank HSS-Co 5%

Centre cutting, used for profile milling, milling keyways and producing open slots. Surface treatment: bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

Short Series - Inch

Kennedy® Screw Drills Solid Carbide

Primarily designed for removing broken taps or bolts without damaging the component surface. By drilling the core of a tap it is possible to remove the remaining pieces with a scriber. Screw Drills are also suitable for drilling other hard materials including: hardened steels, glass, stellite etc. Select screw drill as per tap diameter. Steady manual feed component and spindle stability are vital. Drills should be running between 1500 and 3500 revs/min. A steady and continuous manual feed should be applied. No cutting fluid required.

For all technical specifications please refer to our catalogue.

Screw Drill Solid Carbide - Metric

3 Flute Taper Shank Countersinks

These three flute Sherwood 90 countersinks are manufactured from HSS-E cobalt steel with a ground finish. They are suitable for deburring and chamfering most metals and plastics. Manufactured to BS328:Part 5:1983.

For all dimensional specifications please refer to our catalogue.

90 Degrees

Sherwood Taps

Sherwood HSS Taps are the general purpose option for thread cutting in most materials including steel, some stainless steels, cast irons and non-ferrous materials such as Aluminium, Brass and many others.

Manufactured with precision ground flutes for producing accurate thread forms, Sherwood Taps are available in all the popular thread forms and as straight Flute `Hand` Taps in 3 leads, Fluteless, Spiral Flute, or Spiral Point Machine Taps and also Long Series.

Sherwood Tap dimensions conform to ISO529 apart from NPT Forms which conform to ANSI 94.9. Straight Flute and Fluteless Taps are manufactured with a standard Bright Finish whereas the Machine Taps have an Oxidised Finish for best results dissipating the heat build-up associated with these applications.

Thread Forms are Class 2 medium fit tolerance.

For all technical and dimensional specifications please refer to our catalogue.

Second Tap Metric Coarse Long Shank Straight Flute Ground Thread HSS

The Sherwood second tap is used after the taper tap has cut threads into the hole as far as possible. It tapers back 3 or 4 threads before a fully threaded diameter is reached. If threading a blind hole a Plug tap will be required to cut threads to the bottom of the hole.