Dormer HSCO Jobber Drills

A900 Multi Application HSCo Jobber Drills Bright.
High productivity one-hit drilling across a wide range of materials.
130° special point geometry ensures consistent hole size and quality throughout the full depth of the hole.
Size Range: A900 (6xD) - 1.0-20.0mm, 3/64-25/32 Inch.

A900 HSCO Jobber Drills Bright

A900
Excellent for: Carbon/alloy steels, stainless, titanium and nickel
Good for: Cast iron, copper, aluminium and thermoplastics

Dormer Solid Carbide Drills

The new Dormer MP-X range of multi-application carbide drills are cost effective, high performance drills that offer high productivity and supreme value for money. A wide range of materials can be machined using a minimum number of drills, to reduce stock-holding and associated costs.

MP-X Solid Carbide Drills

Dormer MP-X solid carbide drills deliver the following benefits and features:

Benefits
? Exceptional value with no compromise on quality.
? High productivity.
? Excellent hole quality.
? Availability.
? Reduced tooling costs.

Material
Micro-grain carbide for an excellent combination of hardness and toughness, resulting in high wear resistance and longer tool life.

Coating
Multi-layer titanium aluminum nitride (TiAlN) coating gives:
? Improved stability of cutting edges.
? Outstanding wear protection.
? High hardness properties.
? High toughness and oxidation stability
? Longer tool life and higher productivity.

Flute Geometry
Strong web design gives excellent crosssectional strength and facilitates chip evacuation.

Point Geometry
140 point angle with good centring capabilities and low thrust force design, suited to multiapplication drilling.

Multi-Application
Multi-application drilling across a wide range of materials, including:
? Carbon and alloy steels.
? Stainless steels.
? Cast iron.
? Aluminium.
? Magnesium alloys.
? Copper.

Suitable for Regrinding
The quality of design will allow consistently high levels of performance and tool life after the product is reconditioned, providing further cost reduction benefits.

Indexa-Seiki VDI Toolholders

Manufactured to DIN 69880. Suitable for use in NC lathes with VDI fixing disc. Features: All tools are fully carburised and hardened. Surface hardness of 58 - 60HRC. Tensile strength above 1000N/mm2. Surfaces blued; seat, parallel shank and shoulder ground. Tools can be adjusted in-situ on radial and axial toolholders. Seat shim allows two tool sizes to be used with one toolholder. Ball regulator (bullseye) provides easy coolant control.

E2-3 Morse Taper Sleeves

Guhring Production Jobber Drills HSS-Co 5%

Solid Carbide Jobber drills are especially suitable for drilling cast steels, grey cast iron, chilled cast iron, austenitic manganese steels, bronzes, light metals and non-ferrous metals. Furthermore suitable for the economic machining of abrasive materials (AlSi-alloys), fibre-reinforced plastics and other Duroplastics liable to cause severe abrasion on cutting lips and lands.

Series 5517 - Inch

Swiss+Tech® HSS "Green Ring" Taps

Manufactured to DIN 371/376.

Spiral Flute - HSS-EV Nitride Finish ISO Metric Coarse

For blind holes. Taper lead to DIN form C (2.5 x P). Tapping tolerance to 6H 2B. Helix angle 45°. Tapping depth 2.5 x D.

Sherwood Taps

Sherwood HSS Taps are the general purpose option for thread cutting in most materials including steel, some stainless steels, cast irons and non-ferrous materials such as Aluminium, Brass and many others.

Manufactured with precision ground flutes for producing accurate thread forms, Sherwood Taps are available in all the popular thread forms and as straight Flute `Hand` Taps in 3 leads, Fluteless, Spiral Flute, or Spiral Point Machine Taps and also Long Series.

Sherwood Tap dimensions conform to ISO529 apart from NPT Forms which conform to ANSI 94.9. Straight Flute and Fluteless Taps are manufactured with a standard Bright Finish whereas the Machine Taps have an Oxidised Finish for best results dissipating the heat build-up associated with these applications.

Thread Forms are Class 2 medium fit tolerance.

For all technical and dimensional specifications please refer to our catalogue.

Second Tap UNF (Unified Fine) Long Shank Straight Flute Ground Thread HSS

The Sherwood second tap is used after the taper tap has cut threads into the hole as far as possible. It tapers back 3 or 4 threads before a fully threaded diameter is reached. If threading a blind hole a Plug tap will be required to cut threads to the bottom of the hole.

Kennedy Endmills

Kennedy KC3 throwaway 3* flute endmills are manufactured HSS-Co 5% making them much tougher than HSS. This means that Kennedy endmills can be used at higher speeds and feeds which in turn gives greater productivity.

Kennedy KC3 endmills are available uncoated, TiN coated and TiCN coated.

TiN (Titanium nitride) provides a surface hardness in the region of 2300HV which offers improved wear resistance, tool life and productivity.

TiCN (Titanium Carbonitride) gives a surface hardness in the region of 3000-3500 HV, excellent wear resistance and good heat resistance. This coating is used for the same things as TiN but also for hard steels, stainless, cast iron, brass & bronze.

For all technical and dimensional specifications please refer to our catalogue.

*Except: 1mm cutters, 2mm and 1/16" ball nose cutters, all of which have two flutes.

KC3 Endmill Long Series 3* Flute Throwaway Cutter Weldon Shank HSS-Co 5% - Inch

Starrett Holesaw Kits

A comprehensive range of holesaw kits for cutting virtually any material. Made in Britain, each bi-metal hole saw kit comprises a selection of constant pitch hole saws and accessories. Designed for use in the electrical, plumbing, automotive and locksmith trades, and industry generally, Starrett bi-metal hole saws are durable and shatter resistant and ideal for cutting metal (including stainless steel), wood and plastic. Kits are supplied complete in an attractive, sturdy, carrying case.

General-Purpose 9 Piece Kit (KS2000G)

Contents:
Holesaws: 22mm, 29mm, 35mm, 44mm, 51mm & 64mm.
Arbors: A1 & A10.
Accessories: A7 Ejector spring.

Tungaloy CCMT Indexable Turning Inserts

NS530/NS540 (ISO P05-P20) A finishing grade for steel and stainless steel. Gives a superior and consistent surface finish.

ISCAR?s new Single-Ended Insert for Parting With an Improved Clamping Method

TAG Insert Features
* Very rigid clamping in a tangentially oriented pocket.
* Enables machining at very high feed rates and provides excellent straightness and surface finish.
* Recommended for parting large diameter parts and for * Offers a free, unobstructed chip flow, since there is no upper jaw as in the other clamping systems (very important in deep grooving and parting applications.
* The combination of tangential clamping and free chip flow results in improved tool and insert life time.
* Provides a solution to the problem of inserts being pulled out during retraction.

The TAG inserts are available with the familiar J- and C-Type chipformers, with neutral and angular frontal cutting edges. The new tools are equipped with a user-friendly clamping and extraction device. The TANG-GRIP family includes square shank tools, blades and inserts in 1.4 - 9.5mm widths in the most advanced IC830 and IC808 SUMO TEC grades. The blades are in standard siuzes which fit ISCAR's standard blocks.

Tang-Grip? TAG R/L-C Parting & Grooving Inserts

First choice for soft materials, parting of tubes, small diameters and thin-walled parts. Cutting edge with positive rake. General applications on low carbon steel, alloy steel, austinitic stainless steel. Low-to-medium feed.

IC830 Grade Description:
(P20-P50/M20-M40/K15-K40/ S15-S40) PVD TiAlN coated tough grade followed by a special SUMO TEC surface treatment. Suitable for milling stainless steel, high temperature alloys and other alloy steels. Recommended for interrupted cut and heavy operations.