Dormer Taps

Dormer MTT-X Series taps are manufactured from HSS-X1 Steel with a Bright finish, they are right Hand Cutting.

Manufactured to ISO 529
Spiral Flute for threading blind holes.
Taper lead to DIN form C.
Tapping tolerance to 6H.
Max Depth 2.5 x D.
Helix angle 48.

For all technical and dimensional specifications please refer to our catalogue.

Sherwood Spotting Drills HSS-E

These specially designed drills produce accurate and true positional hole starts for follow-up drills. They provide exceptional alignment accuracy, achieved due to short flute and overall lengths and no body clearance. This very short design allows chucking very close to the point so that they will produce a true start or center. Traditional twist drill bits may tend to wander when started on an unprepared surface. Once a bit wanders off-course it is difficult to bring it back on center. A spot drill bit will provide a far better starting point as it is short and has a reduced tendency to wander. For accurate and fast spotting on NC machines, jig drills and other capital-intensive boring machines. Also suitable for countersinking and chamfering of tapping holes in one operation.
90 point angle - Offers hole chamfering and spotting with one tool.
120 point angle - Specifically for spotting and closely matches a typical drill point. The cutting edges of the following drill will engage easily for perfect hole location.
For all dimensional specifications please refer to our catalogue.

Series C530 - 120 Degree

Sherwood Dies

Sherwood UNC (Unified Coarse) HSS dies are used in diestocks to produce external screw threads.

Thread form to: BS 1580

For all technical and dimensional specifications please refer to our catalogue.

Dies UNC (Unified Coarse) Ground Thread HSS

Kennedy Holesaw Variable Pitch Bi-Metal HSS

Kennedy variable pitch bi-metal high speed holesaws feature a very aggressive cutting action, which gives a very smooth finish and substantial reductions in noise levels. Noise reduction is achieved by disrupting the harmonics produced when sawing certain materials and structures such as tubing and angle. An improvement in swarf clearance is also achieved.

Cutting depth: 28.5mm (1.1/8'').

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

SwissTech 2 Flute Ball Nosed Slot Drills Threaded Shank HSS-Co 8%

Centre cutting. Threaded shank to DIN 1835B. Cutting diameter to e8. Shank diameter to h6. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 40 Long SBH-2TL HSS-Co 8%

Dimensions to DIN 844.

Indexa-Seiki? ER Collets

Indexa-Seiki? ER collets are the most versatile toolholding system for any operation that utilises a round shank cutting tool in a machining centre. Typical applications include drilling, milling, tapping, reaming and boring.

When Indexa-Seiki? ER collets are used with round shank cutting tools the collet chucks centralise the cutting tool and if all the ER system components have been maintained correctly, this should result in increased tool life, higher feed rates, better work piece accuracy and enhanced work piece finish.

ER Collet Set

Indexa-Seiki? ER Collets are available in the in a range of sizes to maximise efficiency in most applications, they are manufactured from hardened and tempered high alloy steel. All supplied in hardwearing bench cases with protective foam inserts.

Conform to DIN 6499.
Up to 10.0mm - 0.015mm TIR.
11.0 to 18.0mm ? 0.015 to 0.020mm TIR.
19.0 to 26.0mm ? 0.015 to 0.020mm TIR.

For all technical and dimensional specifications please refer to our catalogue.

Eclipse Hand Hacksaw Blades Flexible Silicon Steel

General purpose shatterproof blades manufactured from low alloy silicon steel suitable for DIY use cutting mild steel, brass, aluminium and other soft metals and plastics.

Dormer Drills Taper Shank HSS

General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345.

For all dimensional specifications please refer to our catalogue.

Series A130 (MT1) - Metric

Guhring GV120 Heavy Duty Stub Drills HSS-Co

Manufactured to Type GV120 DIN1897.

Series 329

Kennedy® 2 Flute Milling Cutters for Aluminium Carbide Al-Karb Ultrafine Micrograin

Centre cutting as standard. An advanced tool geometry designed for cutting aluminium and other non-metallic, non-ferrous materials requiring high machining rates. Al-Karb cutters will out-perform conventional end mills on these materials as the flute design allows maximum chip removal.Short Series

Short Series 2 Flute - Metric