Sandvik Coromant CoroDrill 880 Indexable Drilling Inserts

Guide to Geometry/Feed:
-GM geometry is the basic choice for most materials. Medium feed.
-LM geometry is the best choice for long chipping materials, e.g. low carbon steel and stainless steels. Medium feed, insert with sharp positive edge.
-GR geometry is the high feed choice for steel and cast iron. Insert with strong reinforced edge, suitable for roughing.
-GT geometry is a problem solver for unstable conditions and interrupted cuts. Low to high feed. Good chip control in most materials.

For all technical and dimensional specifications please refer to our catalogue.

CoroDrill 880 Indexable Drilling Insert

Insert size: 880.. 06 04 W06H-P (Peripheral insert). Geometry: -GM. Grade 4014.

Indexa-Seiki ER Single-Angle Collets

Collet Dimensions:
Capacity 3.0-13.
(D)21mm x (L)31.5mm.

ER20

SwissTech 4 Flute Ball Nosed End Mills Plain Shank Carbide

Centre cutting. To Manufacturers Standards. Cutting diameter to h10. Shank diameter to h6. Available as Carbide Uncoated (for general production machining) or TiCN Coated (extends cutter tool life and improves work material surface finish).

For all dimensional and technical specifications please refer to our catalogue.

Series 56 Short EBT-4PS TiCN Coated

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Iscar Turning Inserts

IC9250 Grade description (P20 - P30, M15 - M30).
A TiCN/Al2O3/TIN multi-layer, CVD coated grade. Especially recommended for grooving and turning forged, low carbon and low-alloyed steel parts. Copes efficiently with machining stainless steel at finishing and medium conditions.

TNMG

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Sherwood Straight Shank Parallel Hand Reamers

Used to produce a close tolerance surface finish by hand in almost any environment i.e. on site or in a workshop. Manufactured to BS 328 : Part 4 : 1990 and DIN 206B.

Spiral Flute Parallel Hand Reamers - Metric

For all dimensional specifications please refer to our catalogue.

Kennedy® Long Series Slot Drills Plain Shank Carbide Micrograin

For optimum performance and maximum swarf removal when plunging, slotting and routing in light alloys, brass, aluminium, non ferrous and other soft materials. Manufactured to USCTi Standards.

For all dimensional and technical specifications please refer to our catalogue.

Long Series 4 Flute Slot Drills - Metric

Centre cutting as standard. For maximum strength when milling harder materials where rapid swarf removal is not needed. 4 flute milling cutters have one of the strongest tooth structures available in solid cutters. Manufactured to Ansi Standards.
Inch Tolerances
Nominal Limits Of Tolerance
Diameter High Low
1/16 - 1/4 0.000 -0.002
17/64 - 1 0.000 -0.003
Metric Tolerances
Nominal Limits Of Tolerance
Diameter High Low
1 - 6 0.000 -0.050
7 - 25 0.000 -0.080
Long Series

Sherwood® Solid Carbide Drills

General-purpose drills for drilling a wide variety of metallic and non-metallic materials. Point angle: 118°. Tolerance of diameter: h7. Tolerance of shank: h6. Supply unit. All diameters - 1 pce. Manufacturing Standard: BS 328, DIN 338.

J102 Solid Carbide Jobber Drills

Guhring Slot Drills

Short rigid end mills to suit all general-purpose profiling applications, including alloyed steels, stainless steels and non-ferrous materials. Centre cutting with a unique Fire coating that is applied in Guhring's own coating plants using the PVD process. This all-around performance coating can achieve two to three times the performance of TiN, and considerably better than TiALN. It has excellent heat resistance as well as high toughness, therefore it is well-suited for interrupted cutting.

For all dimensional and technical specifications please refer to our catalogue.

Series 3663 2 Flute Slot Drills