Sherwood 4, 6 & 8 Flute End Mills Threaded Shank HSS-Co

Used for profile milling and producing open slots. Bright finish. Flute Type : 30° Helix. Manufactured to BS 122: Part 4: 1980.

For all dimensional and technical specifications please refer to our catalogue.

Long Series Type E431T - Metric

EX20 DIN 2184-1 Spiral Flute UNC Taps

Bright Finish

Sherwood Solid Counterbore HSS-E

Used for milling of pre-drilled holes to allow bolt or cap head screws to lie flush with the component surface. Spiral, 3 flute. Medium duty. Manufactured to BS328:5:1983.

For all dimensional specifications please refer to our catalogue.

Spiral 3 Flute Screwed Shank

Dormer Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series A100

ISCAR?s new Single-Ended Insert for Parting With an Improved Clamping Method

TAG Insert Features
* Very rigid clamping in a tangentially oriented pocket.
* Enables machining at very high feed rates and provides excellent straightness and surface finish.
* Recommended for parting large diameter parts and for * Offers a free, unobstructed chip flow, since there is no upper jaw as in the other clamping systems (very important in deep grooving and parting applications.
* The combination of tangential clamping and free chip flow results in improved tool and insert life time.
* Provides a solution to the problem of inserts being pulled out during retraction.

The TAG inserts are available with the familiar J- and C-Type chipformers, with neutral and angular frontal cutting edges. The new tools are equipped with a user-friendly clamping and extraction device. The TANG-GRIP family includes square shank tools, blades and inserts in 1.4 - 9.5mm widths in the most advanced IC830 and IC808 SUMO TEC grades. The blades are in standard siuzes which fit ISCAR's standard blocks.

Tang-Grip? TAG R/L-C Parting & Grooving Inserts

First choice for soft materials, parting of tubes, small diameters and thin-walled parts. Cutting edge with positive rake. General applications on low carbon steel, alloy steel, austinitic stainless steel. Low-to-medium feed.

IC808 Grade Description:
(P15-P30/M20-M30/K20-K40/ S15-S25/N15-N25/H20-H30) SUMO TEC TiAlN PVD coated. A tough submicron substrate. For machining heat resistant alloys, austenitic stainless steel, hard alloys and carbon steel at medium to high cutting speeds. Excellent notch wear and built-up edge resistance.

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Guhring Drills Taper Shank HSS

General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345.

For all dimensional specifications please refer to our catalogue.

Series 245 (MT1) - Metric

Kennedy Engineers' Hand Files Industrial Quality

Two equal surfaces, tapered to knife point. For filing and deburring narrow grooves, slits and gear-teeth. Used principally by tool and die makers on work having acute angles. Available as Smooth Cut, Second Cut and Bastard Cut.

Knife

Smooth Rasp Cut

Indexa-Seiki? Lever Lock External Toolholders

For further technical and dimensional specifications please refer to our catalogue.

PWLN - Right Hand

95 Approach for negative 80 trigon inserts.

Indexa-Seiki? External Toolholders - TOP CLAMP

90 Approach for 11 positive triangular inserts.

CTFP - Right Hand

For further technical and dimensional specifications please refer to our catalogue.