M42 Bi-Metal Bandsaw Blades

Starrett Powerband Gladiator M42 is the ultimate competitor in bi-metal bandsaw blades, providing a universal solution with optimum efficiency in large production cutting operations. A high speed steel M42 cutting edge, incorporating a new tooth design with a positive rake angle and variable pitch, combine to give Powerband Gladiator? M42 the utmost in cutting performance and cost effectiveness.

Powerband Gladiator Welded Loops

Recommended applications for Starrett Powerband Gladiator M42 bandsaw blades:
- High production cutting, full range of steels from mild to stainless up to 45 HRC, nickel-based and non-ferrous alloys
Features and Benefits:
- New tooth design features triple-tempered
- M42 high speed steel with 8% cobalt
- Rockwell C67-69
- Up to 12 positive rake angle
- Fatigue resistant alloy steel backing strip
- High wear and heat resistance
- Variable pitch teeth reduce vibration for smooth, quick cutting
- Easy penetration, excellent chip clearance, reduced noise levels
- Improved surface finish
- Faster, straighter cuts

Starrett Bandsaw Blades

Made from carbon steel with a flexible back, Duratec™ SFB is ideal for economical cutting on easy-to-machine ferrous or non-ferrous metal and wood.
Features: Flexible carbon steel back. Wide range of widths, thickness and pitches.
Benefits: Blades can be run at higher band speeds than standard bi metal blades.
Economical general purpose cutting. Ideal for both contour & straight cutting.
Suitable for light vertical and horizontal machines.
Applications: Wood, plastics.
Non-ferrous foundry materials.
Low alloy and non-ferrous metals.
Furniture, composition board.

OSG Endmills Carbide

OSG WX-EBD series ball nose endmills have a long plain shank and an extended neck for hardened material. High performance micro grain carbide with Ultra WX coating (multi layered composite TiALN).

For use on material up to 50HRC.
For ultra high-speed machine centres.
For deep slotting. Cutting length: 0.8 x D.

The Ultra WX coating has been developed to improve performance in a wide range of materials including nonferrous materials, mild steels, and refined steels This stable performance remains consistent in both wet and dry applications and is intended for a wide range of cutting conditions, from low speed/reduced cutting force applications to high speed/high cutting force applications.

For all technical and dimensional specifications please refer to our catalogue.

WX-EBD Series 2 Flute Ball Nose Endmill Plain Long Shank Carbide

Kennedy Precision Hand Files Industrial Quality

Diameter tapers towards point. Suitable for internal and external concave surfaces. Available in tanged pattern 100mm (4") and 150mm (6") lengths. Manufactured to BS 498: 1990.

Round

Available in Cut 0, 2 and 4.

Kennedy Holesaws Constant Pitch Bi-Metal HSS

Featuring a constant pitch - first choice for cutting thin sheet materials up to 3mm thick. For producing high quality holes in wood, steel, brass, bronze, cast iron, aluminium and plastic. Featuring an hardened HSS cutting edge welded to a tough alloy steel body. Heavy duty shatter-resistant construction; virtually unbreakable.

6 teeth per inch.
38mm (1,1/2") cutting depth.

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

For the complete range of Holesaws and Arbors, please refer to our catalogue.

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Sandvik Coromant CoroDrill 880 Drill Bodies

Stronger drill body with new surface treatment can withstand higher feeds. Wiper geometry for best surface finish. Optimized chip channels for accelerated chip evacuation. Easy identification due to laser marking with drill-, insert- and screw codes on the drill shank.

For all dimensional/technical specifications and for a full range of available Inserts, please refer to our catalogue.

Cylindrical shank - flat according to ISO 9766.

CoroDrill 880 Drill Bodies

Sherwood Straight Shank Parallel Hand Reamers

Used to produce a close tolerance surface finish by hand in almost any environment i.e. on site or in a workshop. Manufactured to BS 328 : Part 4 : 1990 and DIN 206B.

Spiral Flute Parallel Hand Reamers - Metric

For all dimensional specifications please refer to our catalogue.

Diemakers Riffler Files

Swiss Pattern. Available in a complete range of shapes the 15cm are used by diemakers, jewellers, silversmiths, engravers etc. All are double ended with the same cut both ends.

SwissTech Heavy Duty Stub Drills HSS-Co Cobalt TiN Coated

Heavy duty drill made of high quality cobalt material with excellent heat resistance. For drilling steels up to 1,400N/mm2, stainless steel, heat resistant steels and bronze. Ideally suited for volume production on automatics. TiN coating provides longer tool life or increased cutting speeds. Point angle: 135. Helix angle: Normal. Web thickness: Strengthened. Tolerance of diameter: h8. Tolerance of shank: f11. Manufactured to DIN1897RN. Point to DIN1412C.

Series 2020