Guhring GT100 Extra Long Drills HSS-Co 5%

High heat resistant drill with wide chip space for very deep holes in difficult conditions, such as when swarf congestion hinders the flow of coolant to the drill point or when tool overheating arises from other causes. For use in steels and cast steels of high tensile strength (not suitable for lubrication holes in crankshafts). Manufactured to DIN1869.

For all dimensional specifications please refer to our catalogue.

Series 619 - Metric

Guhring Production Drills

Guhring No.5523 Jobber Drill HSS-Co have a tough cobalt substrate that delivers high performance at low cost to produce a general purpose drill for the machining of steel and cast steel (alloyed and unalloyed), , grey cast iron, malleable cast iron, spheroidal graphite iron, sintered iron and graphite with high concentricity characteristics.

No.5523 Jobber Drill HSS-Co

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Guhring Production Jobber Drills HSS-Co 5%

Rigid, high-heat resistant drill with large helix angle of 35. Suited for titanium and titanium alloys, stainless steels and heat resisting austenitic steels. Limited suitability for special alloys such as hastaloy, inconel, nimonic etc. Manufactured to DIN338.

Series 605 - Metric

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Guhring HSS GT100 Straight Shank Extra Length Drills

Manufactured to DIN 1869. Right hand cutting. Flute type GT100 - Guhring’s parabolic flute design is suitable
for a wide range of materials and the most universal - can be used to successfully drill ferrous and non-ferrous materials.
Standard GT100 drills incorporate a 130º point angle with a Type A web thin for maximum efficiency. Nitrided lands.

Series 502 - Metric

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.