Guhring Production Jobber Drills HSS-Co 5%

Rigid, high-heat resistant drill with large helix angle of 35. Suited for titanium and titanium alloys, stainless steels and heat resisting austenitic steels. Limited suitability for special alloys such as hastaloy, inconel, nimonic etc. Manufactured to DIN338.

Series 605 - Metric

Guhring Micro-Precision Drills HSS-Co

Series 301 & 660 are for use in general precision engineering, especially the instrument and clock making industries. Specially designed for drilling high alloyed steels. Manufactured to DIN1899.

For all dimensional specifications please refer to our catalogue.

NC Carbide Machine Chucking Reamers

Guhring carbide NC machine chucking reamers are similar to DIN 8093 with straight shank (h6) for standardised tool clamping in hydraulic or shrink fit chucks. The combination of NC machine chucking reamer and hydraulic, high precision clamping or shrink fit chuck respectively offers highest concentricity and process reliability for the production of holes to required tolerances.

5527 Series NC Carbide Machine Chucking Reamers

Surface finish: bright.
Cutting direction: right hand.
Diameter to within 4.0mm with highly unequal flute spacing.
Left hand spiral flutes.

Diameter Tolerances:
from 0.98 to 5.03mm: 0.000/plus 0.004.
from 5.97 to 12.05mm: 0.000/plus 0.005.

For all dimensional specification please refer to our catalogue.

Guhring Endmills HSS-Co 8%

Short rigid end mills to suit all general-purpose applications, including profiling centre cutting, alloyed steels, stainless steels and non-ferrous materials. Uncoated.

For all dimensional and technical specifications please refer to our catalogue.

Series 3428 4 Flute Endmills

Guhring Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series 205

Guhring Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series 205

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Guhring Jobber Drills HSS TiN Coated

Standard drill for drilling steel and cast steel, alloyed and unalloyed grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Type N, BS328, DIN338RN.

Series 651 - Metric