Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Guhring Production Jobber Drills HSS-Co 5%

High heat resistant drill with wide chip space. Suitable for drilling alloyed and unalloyed steels and castings with a high tensile strength over 800N/mm2. Particularly suitable for drilling hot and cold rolled steels. Manufactured to DIN338.

Series 658 - Metric

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Guhring Production Jobber Drills HSS-Co 5%

High heat resistant drill with wide chip space. Suitable for drilling alloyed and unalloyed steels and castings with a high tensile strength over 800N/mm2. Particularly suitable for drilling hot and cold rolled steels. Manufactured to DIN338.

Series 658 - Metric

Guhring Production Drills

Guhring No.5523 Jobber Drill HSS-Co have a tough cobalt substrate that delivers high performance at low cost to produce a general purpose drill for the machining of steel and cast steel (alloyed and unalloyed), , grey cast iron, malleable cast iron, spheroidal graphite iron, sintered iron and graphite with high concentricity characteristics.

No.5523 Jobber Drill HSS-Co

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Guhring HSS-E 'Green Ring' Taps

Manufactured from HSS-E steel to DIN 371/6. Spiral flute for blind holes. Taper lead to DIN form B (3.5 x P to 5.5 x P). Tapping tolerance to 6HX.

Guhring Stub Drills HSS

Ideally suited for portable drill applications where the shorter flute and stub length offer the extra rigidity normally associated with fixed drilling. Manufactured to BS328:Part 1:1986/DIN1897RN.

Series 223

Guhring Stub Drills Carbide SL

Carbide drills deliver a quantum leap in high speed holemaking performance and tool life that manufacturers have been asking for. Carbide tooling provides faster cutting rates, longer tool life, better positional and dimensional accuracy and improved surface finish. Short cycle times and tighter tolerances translate into maximum machine utilizations, better part quality and optimum holemaking cost savings.

Series 5516

Guhring HSS GT100 Straight Shank Extra Length Drills

Manufactured to DIN 1869. Right hand cutting. Flute type GT100 - Guhring’s parabolic flute design is suitable
for a wide range of materials and the most universal - can be used to successfully drill ferrous and non-ferrous materials.
Standard GT100 drills incorporate a 130º point angle with a Type A web thin for maximum efficiency. Nitrided lands.

Series 502 - Metric