Kennedy® Thredfloer Fluteless Taps

Form rather than cut the thread in almost any ductile material. These include aluminium, brass, copper, carbon steels, zinc and magnesium alloys and even some stainless steels. The material is "cold formed" into the relevant thread and has the advantage of being a full form thread unlike normal cut tapped holes. This make the thread stronger. The forming operation does not create chips so swarf contamination and blockage is illiminated and tap breakage reduced. Because there is no consideration for chip evacuation, Thredfloer taps can be run at higher cutting speeds and reduced cycle times. Lubrication grooves are a feature of all Thredfloer taps of M3.0 and over. These allow lubrication to reach the end of the tap to maintain tool life and to prevent damage from "Hydraulic Blow Out".

Metric Coarse

HSS - EV. Oxide Finish. Tolerance 6H. Manufactured to DIN 371.

Kennedy® Long Series Slot Drills Plain Shank Carbide Micrograin

For optimum performance and maximum swarf removal when plunging, slotting and routing in light alloys, brass, aluminium, non ferrous and other soft materials. Manufactured to USCTi Standards.

For all dimensional and technical specifications please refer to our catalogue.

Long Series 2 Flute Slot Drills - Metric

Kennedy® 3 Flute 60° High Helix End Mills Weldon Shank Carbide

Suitable for the high speed machining of titanium inconel, stainless steel and steel alloys. Cutting diameter to h10. Shank diameter to h6. Dimensions to DIN.

Short Series 3 Flute High Helix - Metric

Kennedy Precision Hand Files Industrial Quality

Equilateral section (60 angles). Tapered towards point. For filing acute angles, internal corners and flat filing, clearing out square corners and for filing HSS tools after machining. Available as Smooth Cut, Second Cut and Bastard Cut. Available in tanged pattern 100mm (4") and 150mm (6") lengths. Manufactured to BS 498: 1990.

Three Square

Available in Cut 0, 2 and 4.

Kennedy Engineers' Hand Files Industrial Quality

Parallel edges, surfaces tapered towards end. Narrow version of hand file. For use where access is restricted. These files are designed for millwrights and mechanics for use in enlarging key-ways, slots, etc., close to the shoulder. Available as Smooth Cut, Second Cut and Bastard Cut.

Pillar

Smooth Cut

Kennedy Toolbits & Parting-Off Blades

Cut faster, 'stand up' longer and reduce costs. Square and rectangular toolbits supplied with 10 bevelled ends. Parting off blades supplied with 2 side taper, 15 bevel (top and bottom).

5% Cobalt Square Metric

Kennedy Toolbits & Parting-Off Blades

Cut faster, 'stand up' longer and reduce costs. Square and rectangular toolbits supplied with 10 bevelled ends. Parting off blades supplied with 2 side taper, 15 bevel (top and bottom).

5% Cobalt Rectangular Inch

Kennedy Industrial Quality Screw Extractors

Recommended for simple, low cost removal of broken screws, bolts etc, without damaging the threads of the component.

For all dimensional specifications please refer to our catalogue.

Kennedy® Ball Nosed Slot Drills Plain Shank Carbide Micrograin

For optimum performance and maximum swarf removal when plunging, slotting and routing in most materials including brass, aluminium, non ferrous and other soft materials. Manufactured to USCTi Standards.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 2 Flute - Inch

For optimum performance and maximum swarf removal when plunging, slotting and routing in light alloys, brass, aluminium, non ferrous and other soft materials. Manufactured to USCTi Standards.
Inch Tolerances
Nominal Limits Of Tolerance
Diameter High Low
1/16 - 1/4 0.000 -0.002
17/64 - 1 0.000 -0.003
Metric Tolerances
Nominal Limits Of Tolerance
Diameter High Low
1 - 6 0.000 -0.050
7 - 25 0.000 -0.080
Regular Length

Kennedy® Milling Cutters Plain Shank Carbide Micrograin

3 Flute
Centre cutting as standard. Offer a combination of advantages achieved with two and four flutes giving profile and peripheral milling capability in addition to slotting and plunging. Manufactured to Works Standards.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 3 Flute Slot Drills - Metric