Kennedy® Brazed Tip Turning and Boring Tools

Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40:
Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30:
Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20:
General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates.

For all dimensional and technical specifications please refer to our catalogue.

Cranked Turning Tools

Left Hand. Available in Grades P40, P30 and K20.

Kennedy High Performance Rotary Impact Drill Bits

Tungsten carbide tipped with fully ground flutes. Full flute width, tip seating and specially designed cutting angles. For rapid drilling of concrete, brick, masonry, etc. Suitable for both rotary and rotary-impact use. Manufactured to BS 5621: 1992, ISO 5468 : 1992.

Extra Length

Kennedy Engineers' Hand Files Industrial Quality

Equilateral section (60 angles). Tapered towards point. For filing acute angles, internal corners and flat filing, clearing out square corners and for filing HSS tools after machining. Available as Smooth Cut, Second Cut and Bastard Cut.

Three Square

Smooth Cut

Kennedy Holesaws Constant Pitch Bi-Metal HSS

Featuring a constant pitch - first choice for cutting thin sheet materials up to 3mm thick. For producing high quality holes in wood, steel, brass, bronze, cast iron, aluminium and plastic. Featuring an hardened HSS cutting edge welded to a tough alloy steel body. Heavy duty shatter-resistant construction; virtually unbreakable.

6 teeth per inch.
38mm (1,1/2") cutting depth.

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

For the complete range of Holesaws and Arbors, please refer to our catalogue.

Kennedy Needle Files Industrial Diamond-Coated 16cm

Available in seven shapes, Hand, Half Round, Three Square, Round, Square, Knife and Flat and two grain sizes, 120/140 and 325/400 offering the solution to finishing problems where material hardness makes conventional files ineffective. Plated with finely selected diamond powder, 120 - 150 mesh. Can be used on tungsten carbide, ceramics, carbon, glass, fibreglass and hardened steels such as stainless steel, nimonics, titanium etc.

Knife

Kennedy Holesaw Variable Pitch Bi-Metal HSS

Kennedy variable pitch bi-metal high speed holesaws feature a very aggressive cutting action, which gives a very smooth finish and substantial reductions in noise levels. Noise reduction is achieved by disrupting the harmonics produced when sawing certain materials and structures such as tubing and angle. An improvement in swarf clearance is also achieved.

Cutting depth: 28.5mm (1.1/8'').

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

Carbide Tipped Holesaws

Kennedy carbide tipped holesaws last up to 10 times longer than standard hole saws and resist wear and heat caused by friction much better than traditional holesaws, making them the best choice for cutting tough material such as tile, stainless steel.

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

Holesaws Carbide Tipped

Kennedy Engineers' Hand Files Industrial Quality

Two equal surfaces, tapered to knife point. For filing and deburring narrow grooves, slits and gear-teeth. Used principally by tool and die makers on work having acute angles. Available as Smooth Cut, Second Cut and Bastard Cut.

Knife

Smooth Rasp Cut

Kennedy Heavy Duty Drills for Stainless Steel HSS-Co 8%

Heavy-duty drill made of 8% cobalt material with excellent heat resistance. To drill steels with tensile strength up to 1,400 N/mm2, very hard bronze, stainless steels as well as heat and acid resistant steels. Point Angle: 135. Helix angle: Normal. Web thickness: Strengthened. Relief angle: Normal. Tolerance of diameter: h8. Tolerance of shank: f11. Manufacturing Standard: DIN338.

HSCo Heavy Duty Drill For Stainless Steel - Series XT34 - Metric

Kennedy Precision Hand Files Needle Pattern (Round Handle)

Available in 14cm and 16cm lengths and a complete range of shapes. Manufactured to BS 498:1990.

Round

Available in Cut 0, 2 or 4.