Kennedy Engineers' Hand Files Industrial Quality

Engineers' Flat Files have edges that taper towards front. Applications as for hand files but without safe edge. Preferred where taper allows access into tight corners and angles. For general work on iron, steel, etc. Available as Smooth Cut, Second Cut and Bastard Cut.

Flat

Second Cut

Carbide Tipped Holesaws

Kennedy carbide tipped holesaws last up to 10 times longer than standard hole saws and resist wear and heat caused by friction much better than traditional holesaws, making them the best choice for cutting tough material such as tile, stainless steel.

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

Holesaws Carbide Tipped

Kennedy Toolbits

5% Cobalt Round.

Kennedy Heavy Duty Drills for Stainless Steel HSS-Co 8%

Heavy-duty drill made of 8% cobalt material with excellent heat resistance. To drill steels with tensile strength up to 1,400 N/mm2, very hard bronze, stainless steels as well as heat and acid resistant steels. Point Angle: 135. Helix angle: Normal. Web thickness: Strengthened. Relief angle: Normal. Tolerance of diameter: h8. Tolerance of shank: f11. Manufacturing Standard: DIN338.

HSCo Heavy Duty Drill For Stainless Steel - Series XT34 - Metric

Kennedy® Ball Nosed Slot Drills Plain Shank Carbide Micrograin

Offer a combination of advantages achieved with two and four flutes giving profile and peripheral milling capability in addition to slotting and plunging. Chatter is also significantly reduced. Centre cutting as standard. Manufactured to Ansi Standards.

For all dimensional and technical specifications please refer to our catalogue.

Long Series 3 Flute - Metric

For optimum performance and maximum swarf removal when plunging, slotting and routing in most materials including brass, aluminium, non-ferrous and other soft materials. Manufactured to ANSI Standards.
Metric Tolerances
Nominal Limits Of Tolerance
Diameter High Low
1 - 6 0.000 -0.050
7 - 25 0.000 -0.080
Long Series

Kennedy Engineers' Hand Files Industrial Quality

Engineers' Flat Files have edges that taper towards front. Applications as for hand files but without safe edge. Preferred where taper allows access into tight corners and angles. For general work on iron, steel, etc. Available as Smooth Cut, Second Cut and Bastard Cut.

Flat

Smooth Cut

Kennedy® Thredfloer Fluteless Taps

Form rather than cut the thread in almost any ductile material. These include aluminium, brass, copper, carbon steels, zinc and magnesium alloys and even some stainless steels. The material is "cold formed" into the relevant thread and has the advantage of being a full form thread unlike normal cut tapped holes. This make the thread stronger. The forming operation does not create chips so swarf contamination and blockage is illiminated and tap breakage reduced. Because there is no consideration for chip evacuation, Thredfloer taps can be run at higher cutting speeds and reduced cycle times. Lubrication grooves are a feature of all Thredfloer taps of M3.0 and over. These allow lubrication to reach the end of the tap to maintain tool life and to prevent damage from "Hydraulic Blow Out".

Metric Coarse

HSS. TiN Coated. Tolerance 6H. Manufactured to DIN 371.

Kennedy Holesaw Variable Pitch Bi-Metal HSS

Kennedy variable pitch bi-metal high speed holesaws feature a very aggressive cutting action, which gives a very smooth finish and substantial reductions in noise levels. Noise reduction is achieved by disrupting the harmonics produced when sawing certain materials and structures such as tubing and angle. An improvement in swarf clearance is also achieved.

Cutting depth: 28.5mm (1.1/8'').

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

Kennedy® Brazed Tip Turning and Boring Tools

Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40:
Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30:
Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20:
General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates.

For all dimensional and technical specifications please refer to our catalogue.

Brazed Tip Cranked Turning & Facing Tools

Left Hand. Available in Grades P40, P30 and K20.

Kennedy Engineers' Hand Files Industrial Quality

Engineers' Half Round Files have edges and surfaces that taper towards the point. Dual application; suitable for concave surfaces and flat filing. For rapid removal of metal. Available as Smooth Cut, Second Cut and Bastard Cut.

Half Round

Bastard Cut