Kennedy SDS-Style Fitting Hammer Drill Bits

Kennedy Tungsten carbide tipped SDS masonry drills are suitable for all SDS direct fitting hammer drills. High performance drill bits that withstand extreme heat generation ensuring maximum performance coupled with wear resistance. Manufactured to DIN 8035.

SDS-Plus Hammer Drill Bit

Kennedy® Thredfloer Fluteless Taps

Form rather than cut the thread in almost any ductile material. These include aluminium, brass, copper, carbon steels, zinc and magnesium alloys and even some stainless steels. The material is "cold formed" into the relevant thread and has the advantage of being a full form thread unlike normal cut tapped holes. This make the thread stronger. The forming operation does not create chips so swarf contamination and blockage is illiminated and tap breakage reduced. Because there is no consideration for chip evacuation, Thredfloer taps can be run at higher cutting speeds and reduced cycle times. Lubrication grooves are a feature of all Thredfloer taps of M3.0 and over. These allow lubrication to reach the end of the tap to maintain tool life and to prevent damage from "Hydraulic Blow Out".

Metric Coarse

HSS. TiN Coated. Tolerance 6H. Manufactured to DIN 371.

Butt-Welded Lathe Tools

Manufactured from top quality sintered steels. For use on a wide range of applications from roughing to finishing. Manufactured to BS1296:Part 3:1978.

For all dimensional and technical specifications please refer to our catalogue.

Parting Off - No.16 R/H/No.16 L/H

Rake and Clearance angles:
Top rake: 5.
Front clearance:
6. Approach angle:
90. Trail angle: 0.
Side clearance: 1-2.

Kennedy High Performance Rotary Impact Drill Bits

Tungsten carbide tipped with fully ground flutes. Full flute width, tip seating and specially designed cutting angles. For rapid drilling of concrete, brick, masonry, etc. Suitable for both rotary and rotary-impact use. Manufactured to BS 5621: 1992, ISO 5468 : 1992.

Extra Length

Kennedy Toolbits

5% Cobalt Round.

Kennedy Engineers' Hand Files Industrial Quality

Engineers' Round Files have a diameter that tapers towards point. Suitable for internal and external concave surfaces. Available as Smooth Cut, Second Cut and Bastard Cut.

Round

Smooth Cut

Kennedy® Stub Length Drills Carbide

For drilling into steel, cast steel, cast iron, chilled cast iron, malleable cast iron, non-ferrous materials and abrasive plastic. Point angle: 118°, helix angle: 30°, tolerance of diameter: h7, tolerance of shank: h6. Manufactured to DIN 6539.

Tolerances:
Cutting Dia. plus 0.000mm - 0.015mm.
Shank Dia. plus 0.000mm - 0.030mm.

Kennedy® Carbide Stub Length Drills - Metric

Kennedy Holesaws Constant Pitch Bi-Metal HSS

Featuring a constant pitch - first choice for cutting thin sheet materials up to 3mm thick. For producing high quality holes in wood, steel, brass, bronze, cast iron, aluminium and plastic. Featuring an hardened HSS cutting edge welded to a tough alloy steel body. Heavy duty shatter-resistant construction; virtually unbreakable.

6 teeth per inch.
38mm (1,1/2") cutting depth.

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

For the complete range of Holesaws and Arbors, please refer to our catalogue.

Butt-Welded Lathe Tools

Manufactured from top quality sintered steels. For use on a wide range of applications from roughing to finishing. Manufactured to BS1296:Part 3:1978.

For all dimensional and technical specifications please refer to our catalogue.

Facing - No.19 RH/No.20 LH

Rake and Clearance angles:
Top rake: 14.
Front clearance: 6.
Approach angle: -30.
Trail angle: 15.
Side clearance: 6.
Corner Radius: 3-8.

Kennedy SDS-Style Fitting Hammer Drill Bits

Kennedy Tungsten carbide tipped SDS masonry drills are suitable for all SDS direct fitting hammer drills. High performance drill bits that withstand extreme heat generation ensuring maximum performance coupled with wear resistance. Manufactured to DIN 8035.

SDS-Plus Hammer Drill Bit