Kennedy® Long Series Slot Drills Plain Shank Carbide Micrograin

For optimum performance and maximum swarf removal when plunging, slotting and routing in light alloys, brass, aluminium, non ferrous and other soft materials. Manufactured to USCTi Standards.

For all dimensional and technical specifications please refer to our catalogue.

Long Series 4 Flute Slot Drills - Inch

Centre cutting as standard. For maximum strength when milling harder materials where rapid swarf removal is not needed. 4 flute milling cutters have one of the strongest tooth structures available in solid cutters. Manufactured to Ansi Standards.
Inch Tolerances
Nominal Limits Of Tolerance
Diameter High Low
1/16 - 1/4 0.000 -0.002
17/64 - 1 0.000 -0.003
Metric Tolerances
Nominal Limits Of Tolerance
Diameter High Low
1 - 6 0.000 -0.050
7 - 25 0.000 -0.080
Long Series

Kennedy Precision Hand Files Industrial Quality

Narrow (Tanged only) alternative to standard pillar file. Available in tanged pattern 100mm (4") and 150mm (6") lengths. Manufactured to BS 498: 1990.

Narrow Pillar

Available in Cut 0 and 2.

Kennedy Heavy Duty Drills for Stainless Steel HSS-Co 8%

Heavy-duty drill made of 8% cobalt material with excellent heat resistance. To drill steels with tensile strength up to 1,400 N/mm2, very hard bronze, stainless steels as well as heat and acid resistant steels. Point Angle: 135. Helix angle: Normal. Web thickness: Strengthened. Relief angle: Normal. Tolerance of diameter: h8. Tolerance of shank: f11. Manufacturing Standard: DIN338.

HSCo Heavy Duty Drill For Stainless Steel - Series XT34 - Metric

Kennedy® Brazed Tip Turning and Boring Tools

Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40:
Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30:
Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20:
General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates.

For all dimensional and technical specifications please refer to our catalogue.

Cranked Round Nosed Turning Tools

Left Hand. Available in Grades P30 and K20.

Kennedy Single Hole Countersinks HSS (5%)

Manufactured from M35 HSS and used for the deburring and chamfering of most metals and plastics.
Straight shank, ground flute.
Manufactured to BS328:Part 5:1983.

For all dimensional specifications please refer to our catalogue.

90° Degrees

Kennedy® High Performance Machine Taps

Made from a super grade high speed steel with extra vanadium content. This has a distinct advantage with taps, by increasing wear resisting properties and extending tool life significantly. These taps are intended for general application where consistent results and improved tool life are important. Threads can be produced in a range of steels, including stainless and cast steels as well as some long chip non-ferrous materials.

Machine Taps Spiral Point Metric Coarse HSS - EV

With straight flutes and short fluted helix at point. Ideal for tapping through holes as swarf is directed ahead of the tap. Flutes are narrower than those of taps required to pull swarf towards the shank and act as lubricant channels, giving greater tap rigidity. Manufactured to BS 949: Part 4: 1990 and ISO 529 : 1975. Tolerance 6H.
Bright finish: standard finish for tapping most materials including low silicon aluminiums, brass, mild steels (low volume) stainless, copper.

Kennedy® Milling Cutters Plain Shank Carbide Micrograin

4 Flute
Centre cutting as standard. For maximum strength when milling harder materials where rapid swarf removal is not needed. 4 flute milling cutters have one of the strongest tooth structures available in solid cutters. Manufactured to Works Standards.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 4 Flute End Mills - Metric

Kennedy® Milling Cutters Plain Shank Carbide Micrograin

3 Flute
Centre cutting as standard. Offer a combination of advantages achieved with two and four flutes giving profile and peripheral milling capability in addition to slotting and plunging. Manufactured to Works Standards.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 3 Flute Slot Drills - Inch

Kennedy Toolbits & Parting-Off Blades

Cut faster, 'stand up' longer and reduce costs. Square and rectangular toolbits supplied with 10 bevelled ends. Parting off blades supplied with 2 side taper, 15 bevel (top and bottom).

5% Cobalt Rectangular Inch

Kennedy Precision Hand Files Industrial Quality

Narrow (Tanged only) alternative to standard pillar file. Available in tanged pattern 100mm (4") and 150mm (6") lengths. Manufactured to BS 498: 1990.

Narrow Pillar

Available in Cut 0 and 2.