Sherwood 4, 6 & 8 Flute End Mills Threaded Shank HSS

Used for profile milling and producing open slots. Bright finish. Flute type : 30° Helix. Manufactured to BS 122 : Part 4 : 1980.

Long Series E430T - Metric

For all dimensional specifications please refer to our catalogue.

Sherwood® Milling Cutters Plain Shank Carbide Micrograin

For optimum performance and maximum swarf removal when plunging, slotting and routing in light alloys, brass, aluminium, non-ferrous and other soft materials. Manufactured to USCTi Standards. Available in 2 flute for maximum swarf clearance, 4 flute for maximum rigidity and 3 flute offers a combination of the advantages achieved with 2 and 4.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 3 Flute Slot Drills

Sherwood Solid Counterbore HSS-E

Used for milling of pre-drilled holes to allow bolt or cap head screws to lie flush with the component surface. Spiral, 3 flute. Medium duty. Manufactured to BS328:5:1983.

For all dimensional specifications please refer to our catalogue.

Spiral 3 Flute Screwed Shank

3/16" - 3/4" BSW Threading Set - 28 Piece

Contents:
Bar Type Tap Wrenches: 1/4"-3/4" & 1/16"-1/4".
Diestock: 1" O/D.
HSS 1" O/D Dies: 1/4" x 2, 5/16" x 18, 3/8" x 16.
HSS Dienuts: 7/16" x 14, 1/2" x 12, 5/8" x 11, 3/4" x 10.
HSSGT Straight Flute Taps:
Taper - 3/8" x 16, 5/16" x 18, 1/4" x 20, 3/16" x 24
Second - 3/4" x 10, 7/16" x 14, 5/8" x 11, 1/2" 12.
Plug - 3/8" x 16, 5/16" x 18, 1/4" x 20, 3/16" x 24.
Tapping Drills to suit: HSS S/S 7.90, 6.50, 9.30, 5.10, 10.50, 3.70mm.

Sherwood Die Nuts

Sherwood ground thread die nuts are suitable for repairing damaged or crossed threads and clearing swarf from threads. When using a die nut (on an existing thread) it is not necessary to apply the same level of precise initial alignment required to form a new thread (i.e. with a die) as the nut will follow the existing threads. They are supplied as hexagon drive allowing them to be turned by a standard spanner or adjustable wrench without the need for a special stock.

Conform to: ISO 529

For all technical and dimensional specifications please refer to our catalogue.



BSF (Fine)

Sherwood Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series J100

Sherwood Drills Taper Shank HSS

General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345.

For all dimensional specifications please refer to our catalogue.

Series T100 (MT1) - Metric

Sherwood 2 Flute Long Series Slot Drills Threaded Shank HSS

Used for milling keyways and slots in one unit. Bright Finish. Flute Type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

For all dimensional specifications please refer to our catalogue.

Metric

Sherwood Taps

Sherwood HSS Taps are the general purpose option for thread cutting in most materials including steel, some stainless steels, cast irons and non-ferrous materials such as Aluminium, Brass and many others.

Manufactured with precision ground flutes for producing accurate thread forms, Sherwood Taps are available in all the popular thread forms and as straight Flute `Hand` Taps in 3 leads, Fluteless, Spiral Flute, or Spiral Point Machine Taps and also Long Series.

Sherwood Tap dimensions conform to ISO529 apart from NPT Forms which conform to ANSI 94.9. Straight Flute and Fluteless Taps are manufactured with a standard Bright Finish whereas the Machine Taps have an Oxidised Finish for best results dissipating the heat build-up associated with these applications.

Thread Forms are Class 2 medium fit tolerance.

For all technical and dimensional specifications please refer to our catalogue.

Spiral Point Tap Metric Fine Straight Flute Ground Thread HSS

Spiral flute taps are used for machine tapping of blind holes as the have a spiral flute that channels the swarf back behind the tap and out of the hole along the flute.

Sherwood Drills Taper Shank HSS

General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345.

For all dimensional specifications please refer to our catalogue.

Series T100 (MT2) - Metric