Sherwood Quick Spiral High Helix Drills HSS

High helix drill for drilling materials like aluminium, aluminium alloys, copper and soft plastics. Point angle 130, helix angle: high, web thickness: standard, relief angle: normal, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS328:Part 1:1986.

Series J300

Sherwood Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series J100

Sherwood Woodruff Cutters Threaded Shank HSS

12mm/1/2" Shank Diameter
Produces closed slots for woodruff keys to DIN 6888. For milling structural, carburizing and heat treated steel up to 900N/mm2. Manufactured to BS 122 : Part 4 : 1980. Made to DIN 850. Shank to DIN 1835/D.

Metric Limits of Tolerances:
Diameter +0.000 -0.127.
Width
2 up to 4 - 0.014 -0.028.
4 up to 7 - 0.020 -0.038.
7mm up - 0.025 -0.047.

Inch Limits of Tolerance:
Diameter +0.015" -0.100".
Width +0.000" -0.001".

For all dimensional specifications please refer to our catalogue.

Inch

Sherwood Straight Shank Parallel Hand Reamers

Used to produce a close tolerance surface finish by hand in almost any environment i.e. on site or in a workshop. Manufactured to BS 328 : Part 4 : 1990 and DIN 206B.

Spiral Flute Parallel Hand Reamers - Inch

For all dimensional specifications please refer to our catalogue.

BA (British Association) HSS Ground Thread Dies

Sherwood dies are for use in die stocks to cut external screw threads on metal rod, the split in the die allows the adjusting screws of the diestock to compress or expand the die to accommodate for slight variations in size of the material being threaded or die sharpness. Sherwood dies are available as Metric Fine, Metric Coarse, UNF, UNC, BA, BSF, BSW, BSPT, BSPF, NPT cutting threads all the dies are manufactured from HSS with precision ground threads to the applicable standard.

For all technical and dimensional specifications please refer to our catalogue.

Sherwood Reduced Shank Drills (Blacksmiths) - 1/2" Parallel Shank HSS

General-purpose drills for light duty work, for drilling steels, cast iron, nickel brass and graphite. Reduced parallel shank 1/2". Point angle 118, helix angle: normal, web thickness: standard, tolerance of diameter: h8, tolerance of shank: -0.01/0.08. Manufactured to BS328. Fracturing of the drill shank may occur if it is used for any other purpose or if extreme pressure is exerted on the drill.

For all dimensional specifications please refer to our catalogue.

Metric

All sizes will fit into a 13mm/1/2" chuck.

Sherwood Gauge Drills HSS Steam Tempered

General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118, helix angle: normal, web thickness: standard, relief angle: 8 - 20, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to ANSI B328, BS 328 and DIN 338.

Number & Letter Gauge Drills:
Gauge drills are still in common use in the U.S. In the past, they were popular elsewhere, but now have been largely discarded in favour of metric sizes. When using a gauge rather than a standard measurement of size the user has to refer to a table of gauge sizes. For example, to drill a hole which is 10 thou (thousandth of an inch .0010) bigger than a 1/8 inch bolt, the user must first work out that 1/8 inch is 125 thou, so the hole size needed is 135 thou, and then must look up in a reference book which gauge drill bit is closest to this diameter - a number 29. Number gauge sizes are similar or equivalent in some respects to, but different from, American wire gauge. Number gauge is usually used from size 80 (the smallest) to size 1 (the largest) followed by letter gauge size A (the smallest) to size Z (the largest). Number gauge is actually defined down to size 97, but these smaller sizes are rarely encountered. It happens that as the technology for making small drill bits and drilling small holes has become more available, metric drills have become the norm.

For all dimensional and technical specifications please refer to our catalogue.

Series J100 - Gauge Sizes

Sherwood Multi Flute End Mills Threaded Shank HSS

Used for profile milling and producing slots. Bright finish. Flute type: 30° helix. Manufactured to BS 122 : Part 4 : 1980.

For all dimensional and technical specifications please refer to our catalogue.

Short Series E410T - Metric

Sherwood® Centre Drills Solid Carbide

Used to produce 60° centres in components for subsequent manufacturing operations to be carried out. Tool life is extended and difficult materials may be drilled.
60° included angle.
118° drill point.
Manufactured to BS 328.
Tolerances:
Cutting diameter 0.0005
Shank diameter 0.0010
For all dimensional specifications please refer to our catalogue.

Sherwood Drills Taper Shank HSS

General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345.

For all dimensional specifications please refer to our catalogue.

Series T100 (MT2) - Metric