Sherwood 2 Flute Slot Drills Threaded Shank HSS

Used for milling keyways and slots in one unit. Bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

For all dimensional and technical specifications please refer to our catalogue.

Short Series S210T - Inch

Sherwood Multi Flute End Mills Threaded Shank HSS

Used for profile milling and producing slots. Bright finish. Flute type: 30° helix. Manufactured to BS 122 : Part 4 : 1980.

For all dimensional and technical specifications please refer to our catalogue.

Short Series E410T - Metric

Sherwood Multi Flute End Mills Threaded Shank HSS

Used for profile milling and producing slots. Bright finish. Flute type: 30° helix. Manufactured to BS 122 : Part 4 : 1980.

For all dimensional and technical specifications please refer to our catalogue.

Short Series E410T - Inch

Sherwood Hand Reamers

Sherwood Taper Pin hand reamers are used to produce a close tolerance surface finish in taper holes to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies.

Manufactured to BS 328 : Part 4 : 1990 and DIN 9A.

For all technical and dimensional specifications please refer to our catalogue.

Taper Pin Hand Reamers - Metric

Sherwood 2 Flute Long Series Slot Drills Threaded Shank HSS

Used for milling keyways and slots in one unit. Bright Finish. Flute Type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

For all dimensional specifications please refer to our catalogue.

Metric

Sherwood Machine Reamers

Sherwood machine reamers are used to produce a close tolerance surface finish by enlarging pre-drilled holes to a finished size. Manufactured from HSS with a 45 bevelled head.

Conform to BS 122 : Part 2 and BS 328 Part 4.

For all technical and dimensional specifications please refer to our catalogue.

Machine Reamers Taper Shank HSS - Metric

Sherwood 4, 6 & 8 Flute End Mills Threaded Shank HSS-Co

Used for profile milling and producing open slots. Bright finish. Flute Type : 30° Helix. Manufactured to BS 122: Part 4: 1980.

For all dimensional and technical specifications please refer to our catalogue.

Long Series Type E431T - Inch

Sherwood Machine Reamers

Sherwood machine reamers are used to produce a close tolerance surface finish by enlarging pre-drilled holes to a finished size. Manufactured from HSS with a 45 bevelled head.

Conform to BS 122 : Part 2 and BS 328 Part 4.

For all technical and dimensional specifications please refer to our catalogue.

Machine Reamers Taper Shank HSS - Metric

3 Flute Straight Shank Countersinks

Sherwood countersinks are a chatter-free cutter that produce an excellent burr-free finish it is capable of deburring and countersinking in one stroke with no "back-off" of tool.
Countersinking a hole leaves an angled conical, chamfered recess on the finished job, for a tapered head bolt or screw to seat correctly into this angled form. Countersink bits can be used for deburring holes as well.
It will also countersink aluminium with no secondary bulge.
Ideal for special applications and exotic materials, a choice of hard coatings is available.

For all dimensional specifications please refer to our catalogue.

100 Degrees

Sherwood® Knuckle Form Ripper Cutters

Sherwood® 'Rippal' 3 flute ripper cutters have centre cutting as standard and as they are manufactured from HSS-Co 8% they operate at higher speeds and feeds than conventional shank milling cutters, removing more metal per minute. The Sherwood® 'Rippal' cutter's unique geometry ensures a more efficient cutting action and reduced cutting time helps you to reduce costs and increase productivity. Power and workholding rigidity must be checked carefully before use as it is recommended that 'Rippal' cutters are used with consistent power feed rates to eliminate backlash.

Sherwood® 'Rippal' cutters are available polished or unpolished and with a weldon or combination shank.

1930M Series 3 Flute 'Rippal' Ripper Cutters Combination Shank HSS-Co 8%