Sherwood 2 Flute Slot Drills Threaded Shank HSS

Used for milling keyways and slots in one unit. Bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

For all dimensional and technical specifications please refer to our catalogue.

Short Series S210T - Inch

3 Flute Straight Shank Countersinks

These three flute Sherwood 90 countersinks are manufactured from HSS-E cobalt steel with a ground finish. They are suitable for deburring and chamfering most metals and plastics. Manufactured to BS328:Part 5:1983.

For all dimensional specifications please refer to our catalogue.

90 Degrees

Set of 6 sizes: 8mm, 10mm, 12.5mm, 16mm, 20mm & 25mm. Supplied in wooden box.

Sherwood® Taper Sheet & Tube Drills HSS

For producing clean holes in sheet metal and other thin-walled materials. Efficient cutting geometry, no pre-drilled pilot hole and the diameter of the finished hole is infinitely variable within the range of each drill, according to depth of feed.

For all dimensional specifications please refer to our catalogue.

Taper Sheet and Tube Drill

Sherwood 4, 6 & 8 Flute End Mills Threaded Shank HSS

Used for profile milling and producing open slots. Bright finish. Flute type : 30° Helix. Manufactured to BS 122 : Part 4 : 1980.

Long Series E430T - Metric

For all dimensional specifications please refer to our catalogue.

Sherwood® Slitting Saw Blades

Sherwood® HSS slitting saws are used for cutting metal, these small diameter saws are hollow ground to give the clearance necessary for deep cutting.

Sizes up to 1" diameter do not have key ways.

For all technical and dimensional specifications please refer to our catalogue.

Slitting Saw Small Diameter HSS

Sherwood Machine Reamers

Left hand spiral flute, right hand cutting. Manufactured to BS 122.

For all dimensional specifications please refer to our catalogue.

Inch

Sherwood Machine Reamers

Sherwood extra length machine reamers are used to produce a close tolerance surface finish by enlarging pre-drilled holes to a finished size to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies.

Manufactured from HSS with a 45 bevelled head.

Conform to BS 328 : Part 4 : and DIN 9A.

For all technical and dimensional specifications please refer to our catalogue.

Machine Reamers Extra Length Taper Shank HSS - Metric

Sherwood Woodruff Cutters Threaded Shank HSS

12mm/1/2" Shank Diameter
Produces closed slots for woodruff keys to DIN 6888. For milling structural, carburizing and heat treated steel up to 900N/mm2. Manufactured to BS 122 : Part 4 : 1980. Made to DIN 850. Shank to DIN 1835/D.

Metric Limits of Tolerances:
Diameter +0.000 -0.127.
Width
2 up to 4 - 0.014 -0.028.
4 up to 7 - 0.020 -0.038.
7mm up - 0.025 -0.047.

Inch Limits of Tolerance:
Diameter +0.015" -0.100".
Width +0.000" -0.001".

For all dimensional specifications please refer to our catalogue.

Metric

3 Flute - Straight Shank

Manufactured from M35 HSS and used for the deburring and chamfering of most metals and plastics.
Manufactured to BS 328 : Part 5 : 1983.
Inclusive angle 82°.

Sherwood Hand Reamers

Sherwood Taper Pin hand reamers are used to produce a close tolerance surface finish in taper holes to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies.

Manufactured to BS 328 : Part 4 : 1990 and DIN 9A.

For all technical and dimensional specifications please refer to our catalogue.

Taper Pin Hand Reamers - Metric