Sherwood 2 Flute Slot Drills Threaded Shank HSS

Used for milling keyways and slots in one unit. Bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

For all dimensional and technical specifications please refer to our catalogue.

Short Series S210T - Metric

Sherwood® Slitting Saw Blades

Sherwood® HSS slitting saws are used for cutting metal, these small diameter saws are hollow ground to give the clearance necessary for deep cutting.

Sizes up to 1" diameter do not have key ways.

For all technical and dimensional specifications please refer to our catalogue.

Slitting Saw Small Diameter HSS

Sherwood Multi Flute End Mills Threaded Shank HSS

Used for profile milling and producing slots. Bright finish. Flute type: 30° helix. Manufactured to BS 122 : Part 4 : 1980.

For all dimensional and technical specifications please refer to our catalogue.

Short Series E410T - Metric

3 Flute Straight Shank Countersinks

Sherwood countersinks are a chatter-free cutter that produce an excellent burr-free finish it is capable of deburring and countersinking in one stroke with no "back-off" of tool.
Countersinking a hole leaves an angled conical, chamfered recess on the finished job, for a tapered head bolt or screw to seat correctly into this angled form. Countersink bits can be used for deburring holes as well.
It will also countersink aluminium with no secondary bulge.
Ideal for special applications and exotic materials, a choice of hard coatings is available.

For all dimensional specifications please refer to our catalogue.

90 Degrees

Sherwood® Milling Cutters Plain Shank Carbide Micrograin

For optimum performance and maximum swarf removal when plunging, slotting and routing in light alloys, brass, aluminium, non-ferrous and other soft materials. Manufactured to USCTi Standards. Available in 2 flute for maximum swarf clearance, 4 flute for maximum rigidity and 3 flute offers a combination of the advantages achieved with 2 and 4.

For all dimensional and technical specifications please refer to our catalogue.

Kennedy® Regular Series 2 Flute Slot Drills

Sherwood Straight Shank Parallel Hand Reamers

Used to produce a close tolerance surface finish by hand in almost any environment i.e. on site or in a workshop. Manufactured to BS 328 : Part 4 : 1990 and DIN 206B.

Spiral Flute Parallel Hand Reamers - Metric

For all dimensional specifications please refer to our catalogue.

HSS-Co 8% Cobalt Long Series Milling Cutters 2 Flute

Centre cutting, used for profile milling, milling keyways and producing open slots. Surface treatment: bright finish.
Flute type: 30° Helix. Overall dimensions to DIN 844. Plain shank to DIN 1835A.

Long Series

HSS-Co. 8% Plain Shank Milling Cutter 4 Flute

Centre cutting, used for profile milling, milling keyways and producing open slots.
Bright finish. Flute type: 30° helix.
Overall dimensions to DIN 844.
Plain shank to DIN 1835A.

Metric Tolerances
Nominal Dia. Limits of Tolerance
Up to 38mm 0.0630 -0.0130
Above 38mm 0.1250 -0.0000

Long Series

Sherwood® Knuckle Form Ripper Cutters

Sherwood® 'Rippal' 3 flute ripper cutters have centre cutting as standard and as they are manufactured from HSS-Co 8% they operate at higher speeds and feeds than conventional shank milling cutters, removing more metal per minute. The Sherwood® 'Rippal' cutter's unique geometry ensures a more efficient cutting action and reduced cutting time helps you to reduce costs and increase productivity. Power and workholding rigidity must be checked carefully before use as it is recommended that 'Rippal' cutters are used with consistent power feed rates to eliminate backlash.

Sherwood® 'Rippal' cutters are available polished or unpolished and with a weldon or combination shank.

930MP Series 3 Flute 'Rippal' Ripper Cutters Weldon Shank HSS-Co 8%

The 930MP 'Rippal' cutters have polished flutes making suitable for use when cutting aluminium to ensure optimum swarf removal.

Sherwood Spiral Flute Chucking Reamers Straight Shank Cobalt HSS-E

The European version of machine reamers ideally suited for use on high performance CNC machines. They are also available, to special order, with a higher cobalt content or made from solid carbide for the machining of tougher more exotic materials. Manufactured to DIN 212 B.

For all dimensional specifications please refer to our catalogue.

Metric