Single Row Deep Groove Ball Bearings - C3 Internal Clearance

C3 Bearings have an internal clearance to cope with high speed environments where excess heat is generated.

Shielded Type

With metal shields inserted into the outer raceway, these fit in closely to the inner race providing moderate protection against mechanical damage, and against the ingress of moisture, dust and other foreign objects. The shields also retain the pre-filled grease in the bearing. Shields can be easily removed for applications that only require one shield.

SNR Shaft Seals & Adaptors

SNC bearing housings can be used for both fixed and floating bearing arrangements. Locating rings enable the bearing to be fixed in place axially. The width of the locating rings is adapted to the bearing being used. To secure the bearings, two locating rings per housing are required.

Locating Rings

Lock Nuts

Used primarily to help lock and locate bearings on shafts or adaptor sleeves. They have evenly spaced slots on the circumference for use with the SNR range of hook spanners.

Narrow Section Wrapped V-Belts conform to DIN 7753 and BS 3790. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 1813. Insensitive to dust. Suitable for tropical climates.
Belt Section 13/A (SPA/13)

Conti-V Ultraflex V-Belts

Single Row Deep Groove Ball Bearings - C3 Internal Clearance

C3 Bearings have an internal clearance to cope with high speed environments where excess heat is generated.

Open Type

Without seals to allow for the free circulation of either oil or grease, used in gearboxes and other assemblies where a lubricant is already present.

SK High Power Wedge Belts

To ISO 4184, BS 3790, DIN 7753 and
USA Standard RMA/MPTA.
The wrapped Optibelt SK wedge belt has been developed with mechanical engineering in mind.
It transmits substantially more power than the classical V-belt with comparable top width.
The Optibelt SK high performance wedge belt is preferred for use in heavy mechanical engineering with very high load requirements, which can be over 2000kW.
*Belts marked are part of the S = C PLUS range with an efficiency of approximately 97% and are suitable for use and require no service or adjustment during service life.

Belt Section 10/Z (SPZ/10)

Cast Iron Motors - 2P

Cast Iron Frame Motors - IE2 (Eff1 Premium Efficiency). Suitable for inverter duty applications. Regreasing nipple from frame 225S/M and above. Thermistors (1 per phase) fitted in
frame 160M and above.

Cast Iron - B5 - Flange Mounted - 2 Pole - 3,000rpm - AC 3 Phase

Taper Bore Bushes

Used to fit flywheels, pulleys and chain sprockets onto an electric motor shaft.
Taper Bore Bushes are easily assembled and are an ideal method of mating to a shaft without the need for machining.
To lock the shaft tighten up two grub screws,
to unlock it you remove the screws, inserting one in the third hole and wind in to lever off the hub from the shaft.
Material: EN-GJL 200/DIN EN 1561.

Metric Sizes

Keyways to DIN 6885 Part 1.
* Bores marked have shallow keyways.

Aluminium Motors 2P

Aluminium Frame Motors - IE2 (Eff1 Premium Efficiency).
Suitable for inverter duty applications.
Thermistors (1 per phase), fitted in frame 132M and above.

Aluminium - B5 - Flange Mounted - 2 Pole - 3,000rpm - AC 3 Phase

Weg Frequency Inventers

The WEG CFW series of Variable Speed Drive (VSD) is intended for speed control of three-phase induction motors.
Applications: Centifugal Pumps, Process Pumps, Fans/Exhausters, Stirrers/Mixers, Extruding Machines, Conveyors, Roller Tables, Granulators, Pelletising Machines, Driers,
Rotating Ovens, Rotating Filters, Winders, Unwinding Machines, Cutting and Welding Machines.

CFW-11

CFW-11 can be used in a vast range of applications, since it is designed for running on either normal or heavy duty cycle loads. The CFW-11 was developed based on plug-and-play philosophy allowing simple and fast installation of the inverter and its accessories. The HMI has a navigation and programming system similar to mobile phones, with soft-key buttons. It is possible to access the parameters sequentially or through groups of parameters. The HMI also makes the Oriented Start-up function available, guiding the user through the necessary programming. A broad
range of accessories can also be easily installed. Comes with the SoftPLC function that attributes PLC functions to the inverter, which allows the customer to create his/her own applications through the WLP.

Dimensions (H x W x D): 247 x 145 x 227mm.

Weight: 0.9kg.