Table Top Slat Chain

A complete range of table top chains and sprockets in steel, stainless steel and molded thermoplastics. These are manufactured specifically for a conveying applications.
Some table top chains have been standardised between manufacturers. We show below the most popular ranges but with many specialty attachments and options available on table top chain, please contact your local service centre to assist in identifying and recommending the right table top chain for your application.

981T Series TAB - Side Flexing Chain

Reduced Flight Gap
Material: Superior grade of cold
rolled special ferritic
stainless steel
Length: 10?

Cylindrical Roller Bearings

Single row cylindrical roller bearings with inner and outer rings. Several styles are available in this series with one or two ribs on either the inner or outer rings. These can support high radial loads and higher speeds due to the cage design than the full compliment designs. The bearings are separable and easier to fit and dismantle.

Non-Locating Type with two Ribs on Inner Ring and Outer Ring is without Ribs

V-Grooved Pulleys for Taper Bushes

Grooves to ISO/BS/DIN 2211.

Belt Section 17/B (SPB/17)

IH025

The IH 025 VOLCANO marks the start of a new era of portable induction heaters. You can use it to heat bearings with an inner diameter as small as 20mm up to on outer diameter of 160mm and a weight of up to 10kg for easy fitting.

• Portable, compact and very light (3.5 kg)
• A 5kg bearing can be heated to 110°C in less than four minutes.
• No support yokes required – simply place the bearing on the cone (20mm to 160mm o/d with just one
portable device)
• Predictive Temperature Control (PTC) for automatic temperature monitoring.
Ask your local service centre today for more information on this unique time saving product.


SIMAIH025-VOLCANO/230V

Optibelt Timing Belts

Optibelt?s Alpha timing belts are manufactured from high grade polyurethane with steel reinforcing cords.

High precision profile for good repeatability.
Very low stretch.
Resistant to many oils and chemicals.
Wide and flexible range.

Alpha Polyurethane Timing Belts

T-Pitch Range - T2.5, T5, T10

SK High Power Wedge Belts

To ISO 4184, BS 3790, DIN 7753 and
USA Standard RMA/MPTA.
The wrapped Optibelt SK wedge belt has been developed with mechanical engineering in mind.
It transmits substantially more power than the classical V-belt with comparable top width.
The Optibelt SK high performance wedge belt is preferred for use in heavy mechanical engineering with very high load requirements, which can be over 2000kW.
*Belts marked are part of the S = C PLUS range with an efficiency of approximately 97% and are suitable for use and require no service or adjustment during service life.

Belt Section 10/Z (SPZ/10)

Taper Roller Bearings

Tapered roller bearings are comprised of solid inner and outer rings with raceways, taper rollers and cages manufactured from pressed steel. The bearings are not self-retaining. As a result, the inner ring with the rollers can be fitted separately from the outer ring. Tapered roller bearings are not sealed and not supplied grease filled.

SNR Bearings

SNR has developed a complete range of high quality ball thrust bearings. Thrust bearings are designed to maintain the shaft in one single direction. They admit low rotating speeds and sustain high axial loads.

You are strongly advised against submitting them to radial loading. Ball thrust bearings are comprised of separate items facilitating installation and maintenance. Grease and oil lubrication is feasible.

Applications: vertical shaft, lathe tailstock, plate-type pumps.

51100 Series Ball Thrust Bearings

Taper Roller Bearings

Tapered roller bearings are comprised of solid inner and outer rings with raceways, taper rollers and cages manufactured from pressed steel. The bearings are not self-retaining. As a result, the inner ring with the rollers can be fitted separately from the outer ring. Tapered roller bearings are not sealed and not supplied grease filled.

SK High Power Wedge Belts

SK wedge belts offer significant performance advantages with up to 97% drive efficiency with extended belt life and easier fitting.
S=C Plus length tolerance* Belts are automatically length matched to very tight tolerances and so require no matching, are easier to fit and run more efficiently in sets.
Example: SPC 5000 tolerance range = +/-2mm compared to DIN standard/other manufacturers = +/-50mm
Advanced manufacturing techniques like our rotational curing process mean that our SK belts are less prone to fatigue and absorb less power in wrapping around the pulley, resulting in improved drive efficiency and longer belt life.
*applies to belts over 1160mm length. Consult catalogue for details.
Dimensions: 487 to 12500mm.
Standard range further sizes on request.

Belt Section 17/B (SPB/17)