Taper Bore Bushes

Used to fit flywheels, pulleys and chain sprockets onto an electric motor shaft.
Taper Bore Bushes are easily assembled and are an ideal method of mating to a shaft without the need for machining.
To lock the shaft tighten up two grub screws,
to unlock it you remove the screws, inserting one in the third hole and wind in to lever off the hub from the shaft.
Material: EN-GJL 200/DIN EN 1561.

Inch Sizes

Keyways to BS 46 Part 1.

Elastomeric Couplings

Rexnord Viva Couplings feature a two-piece flex element design allows for simple replacement without disturbing hubs or moving and realigning connected equipment. Tough polyurethane material is bonded to a corrosion resistant coated shoe, eliminating the need for mechanical clamping hardware. Adhesive coated high strength carbon steel shoe resists corrosion. Easily aligned reversible hubs accommodate multiple shaft gaps. Hubs are available in rough bore, custom bore, or bushed designs. Optional hub materials are available. High grade cap screws are provided with self locking nylon thread patches. Stainless steel cap screws are also available. Torsionally soft polyurethane element cushions shock loads, accommodates unavoidable misalignment and is compatible with most environments. ?V? notch design directs stress concentration away from the bond area providing a uniform failure area for overload protection if required.

Viva Spacer Elements

Single Row Deep Groove Ball Bearings - C3 Internal Clearance

C3 Bearings have an internal clearance to cope with high speed environments where excess heat is generated.

Open Type

Without seals to allow for the free circulation of either oil or grease, used in gearboxes and other assemblies where a lubricant is already present.

Cylindrical Roller Bearings

Single row cylindrical roller bearings with inner and outer rings. Several styles are available in this series with one or two ribs on either the inner or outer rings. These can support high radial loads and higher speeds due to the cage design than the full compliment designs. The bearings are separable and easier to fit and dismantle.

Non-Locating Type with two Ribs on Inner Ring and Outer Ring is without Ribs

Elastomeric Couplings

Rexnord Omega couplings are non-lubricated, material-flexing couplings utilising a specially formulated polyurethane material engineered for maximum durability, strength and fatigue resistance. The flex element is designed to split in half, allowing simplified assembly and disassembly. Interchangeable hubs allow for reduced inventory. High misalignment capacity accommodates unavoidable misalignment with low reactionary forces. Torsionally soft flex element cushions shock loads and vibration extending equipment life. Polyurethane flex element does not require lubrication. Polyurethane-to-metal bond eliminates assembly and slippage problems associated with mechanically clamped designs.

Omega Close Coupled Elements

VB Classical V-Belt

V-Belts to BS3790, DIN2215 and ISO 4184.



Belt Section 17/B (SPB/17)

Conti-V Standard Multiflex V-Belts

Classical section wrapped V-belts to DIN 2215. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 813. Insensitive to dust. Suitable for tropical climates.

Belt Section 13/A (SPA/13)

Max Width (b1) 13mm, Height (h)8mm.

Single Row Deep Groove Ball Bearings - C3 Internal Clearance

C3 Bearings have an internal clearance to cope with high speed environments where excess heat is generated.

Rubber Sealed Type

With rubber seals inserted into the outer raceway and in contact with the inner race providing protection against the ingress of moisture, dust and other foreign objects. The seals also retain the pre-filled grease in the bearing. Seals can be easily removed for applications that only require one seal.

SK High Power Wedge Belts

SK wedge belts offer significant performance advantages with up to 97% drive efficiency with extended belt life and easier fitting.
S=C Plus length tolerance* Belts are automatically length matched to very tight tolerances and so require no matching, are easier to fit and run more efficiently in sets.
Example: SPC 5000 tolerance range = +/-2mm compared to DIN standard/other manufacturers = +/-50mm
Advanced manufacturing techniques like our rotational curing process mean that our SK belts are less prone to fatigue and absorb less power in wrapping around the pulley, resulting in improved drive efficiency and longer belt life.
*applies to belts over 1160mm length. Consult catalogue for details.
Dimensions: 487 to 12500mm.
Standard range further sizes on request.

Belt Section 17/B (SPB/17)

Deep Groove Ball Bearings - C3 Clearance

C3 bearings have an additional internal radial clearance to cope with high speed environments where excess heat is generated.

Shielded type:

With metal shields inserted into the outer raceway, these fit in closely to the inner race providing moderate protection against mechanical damage, and against the ingress of moisture, dust and other foreign objects. The shields also retain the pre-filled grease in the bearing. Shields can be easily removed for applications that only require one shield.