Conti-V Standard Multiflex V-Belts

Classical section wrapped V-belts to DIN 2215. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 813. Insensitive to dust. Suitable for tropical climates.

Belt Section 17/B (SPB/17)

Max Width (b1) 17mm, Height (h)11mm.

Roller Chain

Renold Blue Box chain with their unique control over pin/bush contact, ensures that little initial chain adjustment is therefore required. Renold Blue Box roller chain is highly fatigue resistant with breaking loads exceed the minimum requirements of the international standards.
The specification of Renold chain has evolved from decades of design, test and application experience which delivers product reliability and consistency. Other sizes from 5/16” to 2” pitch are also available please ask for details.
Conforms to: DIN8187/IS606

Triplex Chain

VB Classical V-Belt

V-Belts to BS3790, DIN2215 and ISO 4184.



Belt Section 13A (SPA/13)

Deep Groove Ball Bearings - C3 Clearance

C3 bearings have an additional internal radial clearance to cope with high speed environments where excess heat is generated.

Rubber sealed type:

With rubber seals inserted into the outer raceway and in contact with the inner race providing protection against the ingress of moisture, dust and other foreign objects. The seals also retain the pre-filled grease in the bearing. Seals can be easily removed for applications that only require one seal.

Self-Aligning Ball Bearings

2200 & 2300 Series self-aligning ball bearings are double row with a concave raceway to allow approximately 4° of misalignment. They have a tapered bore for use with adaptor sleeves. There are also a range of sealed versions available.

Cylinder Bore

Narrow Section Wrapped V-Belts conform to DIN 7753 and BS 3790. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 1813. Insensitive to dust. Suitable for tropical climates.
Belt Section 13/A (SPA/13)

Conti-V Ultraflex V-Belts

Taper Roller Bearings

Tapered roller bearings are comprised of solid inner and outer rings with raceways, taper rollers and cages manufactured from pressed steel. The bearings are not self-retaining. As a result, the inner ring with the rollers can be fitted separately from the outer ring. Tapered roller bearings are not sealed and not supplied grease filled.

Thrust Ball Bearings

Thrust Bearings are designed primarily to support axial loads at contact angles between 30° and 90°. Just as with radial bearings, these bearings differ according to the type of rolling element they use. With thrust bearings, it is necessary to supply an axial preload in order to prevent slipping movement between the bearing's rolling element and raceways.
Comprising of caged ball bearing element and pair of shaft housing washers (bearing shaft washer and housing washer, and the normal contact angle is 90°. Axial loads can be supported in only one direction, radial loads cannot be accommodated. Spherical roller and needle roller versions are also available.

Angular Contact Bearings - Double Row

Double-row angular-contact ball bearings accept axial loads in both directions and can be used singly, as dual bearing units.? withstand axial loads in both directions? accept relatively high speeds of rotationThe construction of these bearings limits them to very small misalignment values, in the range of 0.06.

Series 32...A, 33...A

Contact angle 25, no filling slots and can accept axial loads in both directions. These bearings have synthetic material cages.

Conti-V Standard Multiflex V-Belts

Classical section wrapped V-belts to DIN 2215. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 813. Insensitive to dust. Suitable for tropical climates.

Belt Section 17/B (SPB/17)

Max Width (b1) 17mm, Height (h)11mm.