Senator® Diamond Dressing Tools

For truing and dressing grinding wheels. Truing is the process of aligning the periphery of the grinding wheel so that it runs concentric with it's axis of rotation. This allows accurate and precise relative motion between the grinding wheel and the part being ground. Dressing removes dulled abrasive and foreign material that has been embedded into the wheel. This allows the wheel to cut properly. These tools are mainly used to true straight-faced grinding wheels.



For medium duty use. 1/2" dia x 6" shank.

Precision Ground Flat Stock (18")

The dimensional stability of ground flat stock combines with other useful characteristics including excellent resistance to cracking during heat treatment compared with other, more highly alloyed, cold work tools. Relatively soft and easy to machine. High wear resistance after heat treatment. Holds a good cutting edge. Suitable for EDM machining.
Typical applications: widely used in precision tools, machine knives, gauges, jigs, templates, punches, dies and machine parts.
The Cost Cutting Stock: extensive range of widths and thicknesses enables the selection of an appropriate size of ground flat stock to minimise material and machining costs.

Manufactured from BS4659 B01 grade steel equivalent to AISI 01 and Werk. No. 1.2510.
Chemical analysis range:
Carbon 0.90 - 1.00%
Silicon 0.40%
Manganese 1.00 - 1.20%
Chromium 0.50 - 0.70%
Tungsten 0.50 - 0.70%
Vanadium 0.05 - 0.25%

Chemical analysis typical:
Carbon 0.95%
Silicon 0.40%
Manganese 1.20%
Chromium 0.55%
Tungsten 0.55%
Vanadium 0.15%

Inch Sizes

Tolerances:
Thickness: -/+0.001".
Width: -0.00"/+0.005".
Length: -0.00"/+0.25".

Scantool Bending Rolls

All models cover the capacity range of 1.0mm to 3.0mm thickness with a rolling length of 1040mm, these heavily constructed all cast iron framed machines with high quality steel rolls have been designed for ease of operation, all rolls have wire grooves.



Bending Capacity (Width x Thickness): 1040 x 3.0mm
Roll Diameter: 90mm
Operation Type: Motorised
Rolling Speed: 6m/min
Weight: 450kg

Stainless Steel Shim

Precut 300 Series
The best way to solve alignment and levelling problems on motors, pumps, generators and other plant machinery! The pre-cut shims are safer and easier to position as the tab eliminates the need to place hands under machinery during installation or removal of the shim. Engineered for quality, all shim thickness tolerances meet industry standards and conform to standard bolt and stud sizes. Each shim is clearly marked with its thickness.

Stainless Steel Shim

Assorted Packs
Contain ten of each of the above thickness of shim.

Kennedy® Serrated Soft Jaws

To suit metric serrated power chucks (Kitagawa, Howa, Matsumoto, Pratt Burnard, SMW and Autoblok etc).

3 Jaw Sets

Engineers Workbenches

Available with the following worktop finishes.
Wisa - Laminated ply core with mid grey polypropylene face. An easy clean top with good resistance to oil, grease, mild alkalis and weak acids.
Mfc - Particle board core with light grey laminate face. A light duty easy clean top suitable for assembly or office environments.
Mpx - Laminated beech ply. A tough, general duty top suitable for most applications.

Framework bench

A tough steel section framework, braced and finished in RAL7035 grey epoxy powder coat.
The 30mm worktop is available in multiplex or wisa. Full range of accessories available, including overhead kits and suspended cabinets. Flat packed for self assembly.
Height: 780mm.

Kennedy® Industrial Key Steel

High grade mild steel. Available in square or rectangular sections. Metric manufactured from: BS4235 Part 7 1972 grade steel equivalent to DIN 6885. Inch manufactured from: BS46 PART 7 1958 grade steel. Length: 300mm and 12". Other sizes available on request.

Square - Inch

Clamp Fixture Components

Material: Medium Carbon Steel. Hardness: HRC32-38. Surface Finish: Manganese Phosphate

CC06 - Tapped End Plain Clamp

Silver Steel

For tool room and general engineering. Applications include screwdrivers, punches, shafts, axles, pinions, pins, die posts, instrument parts, model parts, taps and drills for mild steel, engraver tools. High carbon content means that it can be hardened to give high wear resistance and chromium content adds strength and hardness.

Manufactured from
BS1407:1970 grade steel.

Typical hardness:
207-237HB with 285HB maximum.

Tensile strength:
45/55 T.P.S.I. (700/850 N/mm2).

Surface finish:
Better than 0.6 microns (25 micro inch) CLA (Centre Line Average).

Chemical analysis range:
Carbon 0.95 - 1.25%
Silicon 0.40% max
Manganese 0.25 - 0.45%
Phosphorous 0.045% max
Sulphur 0.045% max
Chromium 0.35 - 0.45%

Chemical analysis typical:
Carbon 1.13%
Silicon 0.22%
Manganese 0.37%
Phosphorous 0.014%
Sulphur 0.018%
Chromium 0.43%

Metric round sizes

Tolerances:
Up to 25mm plus 0 - 0.012mm.
Over 25mm up to and including 50mm plus 0 - 0.0250mm.