Silver Steel

For tool room and general engineering. Applications include screwdrivers, punches, shafts, axles, pinions, pins, die posts, instrument parts, model parts, taps and drills for mild steel, engraver tools. High carbon content means that it can be hardened to give high wear resistance and chromium content adds strength and hardness.

Manufactured from
BS1407:1970 grade steel.

Typical hardness:
207-237HB with 285HB maximum.

Tensile strength:
45/55 T.P.S.I. (700/850 N/mm2).

Surface finish:
Better than 0.6 microns (25 micro inch) CLA (Centre Line Average).

Chemical analysis range:
Carbon 0.95 - 1.25%
Silicon 0.40% max
Manganese 0.25 - 0.45%
Phosphorous 0.045% max
Sulphur 0.045% max
Chromium 0.35 - 0.45%

Chemical analysis typical:
Carbon 1.13%
Silicon 0.22%
Manganese 0.37%
Phosphorous 0.014%
Sulphur 0.018%
Chromium 0.43%

Inch round sizes

Tolerances:
Below 1" plus/minus 0.00025".
1" up to and including 2" plus/minus 0.00050".

Toggle Clamp Spares

For standard adjustable spindles.

Neoprene Caps

For drawers 1050 x 750mm (W x D)

18 Compartment

Stainless Steel Shim

Precut 300 Series
The best way to solve alignment and levelling problems on motors, pumps, generators and other plant machinery! The pre-cut shims are safer and easier to position as the tab eliminates the need to place hands under machinery during installation or removal of the shim. Engineered for quality, all shim thickness tolerances meet industry standards and conform to standard bolt and stud sizes. Each shim is clearly marked with its thickness.

Wall Mounted Tool Cabinets

Optimise your storage area by using the walls. Pre-punched for wall fixing, ideal for positions above benching or machinery. Fully welded construction. Available in two sizes. 75mm high simple steel drawer units with integral handle. Espagnolette two point locking with flush fitting handle. Adjustable shelves.
Finished in epoxy powder coat - grey/blue.

Toggle Clamp Spares

For use with adjustable 'U' bar type clamps and solid bar type clamps that have bolt retainers.

Neoprene Capped Spindles

Kennedy® Morse Taper Tooling

A range of quality traditional workholding equipment. Manufactured from high quality steel and case hardened all over. All sleeves and sockets are fully hardened and ground internally and externally. ISO 238 BS 1660 : 2.

Turret Sockets

Hook (Latch) Type Industrial Clamps

Features: The action of Hook clamps in pulling two parts together makes them suitable for applications such as closing and holding closed doors, lids, moulds, etc. A benefit of hook clamps is that while the clamp and the pin or latch bracket it engages must be in alignment when viewed from the top, there is no such requirement when viewed from the side - the clamp will lock securely over centre regardless of the angle of the hook. The hook may be engaged either directly to a bolt or pin on one of the parts to be pulled together, or to the latch bracket provided. All hook clamps are fitted with a comfortable, cushioned orange handle grip. Specification: All components are of zinc plated and passivated steel, the hooks being of high tensile alloy steel.

Indexa Die Springs

The heat and surface treatment plus the high quality of steel used in the manufacturing process ensure the springs will bear a high number of stresses without breaking or without appreciable loss of load. Every batch of springs is subject to a rigorous testing procedure to ensure that a consistent quality is maintained. Longer springs should be guided along their course.

Light Load Springs Colour-Coded Green

Steel Locker

Hat shelf and 2 x coat hooks fitted in the single door locker (450mm deep locker also has a hanging rail), 2 x coat hooks fitted in each compartment of the 2-tier locker. BSI Quality Assured (meet the requirements of British Standard for Clothes Lockers BS4680:1996 ?Standard Duty?).

Picture for illustration only not accurate for colour.