Indexa-Seiki External Toolholders - Lever Lock

For further technical and dimensional specifications please refer to our catalogue.

PCBN - Left Hand

75 Approach for negative 80 rhombic inserts.

TNMG Indexable Turning Inserts

QX520 (ISO P10-P35 M10-M30 K10-K30) Coated. An excellent general purpose grade for medium roughing on Steels, Stainless and Cast Irons.

Sherwood Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series J100

Swiss+Tech® HSS "Green Ring" Taps

Manufactured to DIN 371/376.

Spiral Flute - HSS-EV Nitride Finish ISO Metric Coarse

For blind holes. Taper lead to DIN form C (2.5 x P). Tapping tolerance to 6H 2B. Helix angle 45°. Tapping depth 2.5 x D.

Mitsubishi Indexable Turning Inserts

UE6110 (P05-P25)
The first recommendation for steel turning. Suitable for turning various types such as mild steel, carbon steel, bearing steel and lead free steel. High Crater Wear Resistance and High Flank Wear Resistance.

CCMT Indexable Turning Insert

Kennedy High Performance Rotary Impact Drill Bits

Tungsten carbide tipped with fully ground flutes. Full flute width, tip seating and specially designed cutting angles. For rapid drilling of concrete, brick, masonry, etc. Suitable for both rotary and rotary-impact use. Manufactured to BS 5621: 1992, ISO 5468 : 1992.

Medium Length

Indexa-Seiki Tapping Collets

Rigid type. To suit Indexa-Seiki Rigid type tapping chucks.

For all dimensional and technical specifications please refer to our catalogue.

DIN SZ2

HSS-Co. 8% Plain Shank Milling Cutter 4 Flute

Centre cutting, used for profile milling, milling keyways and producing open slots.
Bright finish. Flute type: 30° helix.
Overall dimensions to DIN 844.
Plain shank to DIN 1835A.

Metric Tolerances
Nominal Dia. Limits of Tolerance
Up to 38mm 0.0630 -0.0130
Above 38mm 0.1250 -0.0000

Long Series

Sherwood Spotting Drills HSS-E

These specially designed drills produce accurate and true positional hole starts for follow-up drills. They provide exceptional alignment accuracy, achieved due to short flute and overall lengths and no body clearance. This very short design allows chucking very close to the point so that they will produce a true start or center. Traditional twist drill bits may tend to wander when started on an unprepared surface. Once a bit wanders off-course it is difficult to bring it back on center. A spot drill bit will provide a far better starting point as it is short and has a reduced tendency to wander. For accurate and fast spotting on NC machines, jig drills and other capital-intensive boring machines. Also suitable for countersinking and chamfering of tapping holes in one operation.
90 point angle - Offers hole chamfering and spotting with one tool.
120 point angle - Specifically for spotting and closely matches a typical drill point. The cutting edges of the following drill will engage easily for perfect hole location.
For all dimensional specifications please refer to our catalogue.

Series C520 - 90 Degree

Sandvik Threading Toolholders and Inserts

Sandvik's 266 CoroThread toolholders and inserts provide a high level of stability for threading applications in demanding industries, where precision is paramount.

266 CoroThread ISO Metric Internal Right Hand Threading Insert

Grade description for GC1125:
New PVD-TiAIN-based coating and substrate combine to improve wear resistance and security for threading, providing the option of running at higher cutting speeds or for a longer time in cut.