Indexa-Seiki? Threading Toolholders

Dual DIR - Internal

Internal

BSW (British Standard Whitworth) HSS Ground Thread Dies

Sherwood dies are for use in die stocks to cut external screw threads on metal rod, the split in the die allows the adjusting screws of the diestock to compress or expand the die to accommodate for slight variations in size of the material being threaded or die sharpness. Sherwood dies are available as Metric Fine, Metric Coarse, UNF, UNC, BA, BSF, BSW, BSPT, BSPF, NPT cutting threads all the dies are manufactured from HSS with precision ground threads to the applicable standard.

For all technical and dimensional specifications please refer to our catalogue.

Die BSW (British Standard Whitworth) Ground Thread HSS

Manufactured to: BS1127
Thread Form to: BS84

Guhring Long Series Drills HSS-Co 8%

High heat resistance with wide chip space for use with drill bushings. For drilling alloyed and unalloyed steels and castings with a tensile strength over 800N/mm2. Type N. Manufactured to DIN340.

For all dimensional specifications please refer to our catalogue.

Series 317 - Metric

Dormer HSCo Stub Drills

Excellent for drilling higher tensile, tougher materials
135° split point for improved precision and finish (over 1.5mm).
Manufactured to DIN1897.

HSCo Stub Drills - Series A117 - Metric

AC3000 Carbide Grade (P20 - P40, M20 - M40)

Al2O3 Coated Grade
Designed for interrupted cuts of steels and stainless.

T-Rex TRM55 Carbide Insert

Chip Breaker:
GU Type General purpose Breaker
DOC 1mm-2.5mm
Fz 0.18-0.45mm/rev

Grade Description: AC3000 (Steels) Tough grade for heavy roughing, interrupted cuts and high temperature alloys.

Kennedy® Brazed Tip Turning and Boring Tools

Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40:
Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30:
Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20:
General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates.

For all dimensional and technical specifications please refer to our catalogue.

Cranked Turning Tools

Left Hand. Available in Grades P40, P30 and K20.

Walton 3 & 4 Flute Tap Extractors

Thoroughly remove all chips of the broken tap. insert the extractor fingers into the flutes of the broken tap, pushing them gently but firmly into position. Push the holder down until it touches the broken tap. slide the sleeve down until it touches the work. Apply a tap wrench to the square end of the holder. Twist forward and backward a few times to loosen, then back out the broken tap.

Kennedy Toolbits

HSS Round Inch.

Sherwood 2 Flute Slot Drills Threaded Shank HSS

Used for milling keyways and slots in one unit. Bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

For all dimensional and technical specifications please refer to our catalogue.

Short Series S210T - Inch

AC3000 Carbide Grade (P20 - P40, M20 - M40)

Al2O3 Coated Grade
Designed for interrupted cuts of steels and stainless.

T-Rex TRM55 Carbide Insert

Chip Breaker:
LU Type Finishing Breaker
DOC 0.25mm-1.75mm
Fz 0.025-0.4mm/rev

Grade Description: AC3000 (Steels) Tough grade for heavy roughing, interrupted cuts and high temperature alloys.