SwissTech High Helix Drills for Stainless Steel HSS-Co 8% TiN Coated

Heavy-duty drill for stainless steel, heat and acid-resistant steels, short chipping and high strength steels. High heat resistance allows drilling in titanium and titanium alloys. TiN coating provides longer tool life. Point angle: 130. Helix angle: High. Web thickness: Strengthened. Relief angle: Normal. Tolerance of diameter: h8. Tolerance of shank: f11. Supply unit. All diameters - 1 pce. Manufactured to DIN338RN.

Series 1060 - Metric

Sherwood 2 Flute Long Series Slot Drills Threaded Shank HSS

Used for milling keyways and slots in one unit. Bright Finish. Flute Type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

For all dimensional specifications please refer to our catalogue.

Metric

Kennedy Endmills

Kennedy KC3 throwaway 3* flute endmills are manufactured HSS-Co 5% making them much tougher than HSS. This means that Kennedy endmills can be used at higher speeds and feeds which in turn gives greater productivity.

Kennedy KC3 endmills are available uncoated, TiN coated and TiCN coated.

TiN (Titanium nitride) provides a surface hardness in the region of 2300HV which offers improved wear resistance, tool life and productivity.

TiCN (Titanium Carbonitride) gives a surface hardness in the region of 3000-3500 HV, excellent wear resistance and good heat resistance. This coating is used for the same things as TiN but also for hard steels, stainless, cast iron, brass & bronze.

For all technical and dimensional specifications please refer to our catalogue.

*Except: 1mm cutters, 2mm and 1/16" ball nose cutters, all of which have two flutes.

KC3 Endmill Long Series 3* Flute Throwaway Cutter Weldon Shank HSS-Co 5% TiN Coated - Metric

Swiss+Tech® HSS "Green Ring" Taps

Manufactured to DIN 371/376.

Fluteless - HSS-EV Nitride Finish ISO Metric Coarse

For through and blind holes. Taper lead to DIN form B (4 x P). Tapping tolerance to 6H.

SwissTech Parabolic Deep Hole Drills HSS-Co 8%

Parabolic flute form drill with high heat resistance to non-alloyed and alloyed steels. Chipbreaking point performs well on long chipping materials with a tensile strength up to 1,300 N/mm2. Drills up to 5 x diameter. TiN coating provides longer tool life. Point angle: 130. Helix angle: Normal. Web thickness: Strengthened. Relief angle: Normal. Tolerance of diameter: h8. Tolerance of shank: f11. Supply unit. All diameters - 1 pce. Manufactured to DIN338RN.

Series 1040 - Metric

Kennedy® Ball Nosed Slot Drills Plain Shank Carbide Micrograin

Offer a combination of advantages achieved with two and four flutes giving profile and peripheral milling capability in addition to slotting and plunging. Chatter is also significantly reduced. Centre cutting as standard. Manufactured to Ansi Standards.

For all dimensional and technical specifications please refer to our catalogue.

Long Series 3 Flute - Metric

For optimum performance and maximum swarf removal when plunging, slotting and routing in most materials including brass, aluminium, non-ferrous and other soft materials. Manufactured to ANSI Standards.
Metric Tolerances
Nominal Limits Of Tolerance
Diameter High Low
1 - 6 0.000 -0.050
7 - 25 0.000 -0.080
Long Series

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Taylor & Jones Spiral Flute Bridge Reamers

Have a taper lead angle of 1 in 10 on diameter and are used for reaming pairs of holes which may be out of alignment, particularly with structural steel components, i.e. when assembling pre-drilled steel plate ready for riveting. Previously known as 'Boilermakers' reamers. Manufactured to BS 328 : Part 4 : 1990.

For all dimensional specifications please refer to our catalogue.

Spiral Flute Bridge Reamers - Metric

NC Carbide Machine Chucking Reamers

Guhring carbide NC machine chucking reamers are similar to DIN 8093 with straight shank (h6) for standardised tool clamping in hydraulic or shrink fit chucks. The combination of NC machine chucking reamer and hydraulic, high precision clamping or shrink fit chuck respectively offers highest concentricity and process reliability for the production of holes to required tolerances.

5527 Series NC Carbide Machine Chucking Reamers

Surface finish: bright.
Cutting direction: right hand.
Diameter to within 4.0mm with highly unequal flute spacing.
Left hand spiral flutes.

Diameter Tolerances:
from 0.98 to 5.03mm: 0.000/plus 0.004.
from 5.97 to 12.05mm: 0.000/plus 0.005.

For all dimensional specification please refer to our catalogue.

Indexa-Seiki? ER Collets

Indexa-Seiki? ER collets are the most versatile toolholding system for any operation that utilises a round shank cutting tool in a machining centre. Typical applications include drilling, milling, tapping, reaming and boring.

When Indexa-Seiki? ER collets are used with round shank cutting tools the collet chucks centralise the cutting tool and if all the ER system components have been maintained correctly, this should result in increased tool life, higher feed rates, better work piece accuracy and enhanced work piece finish.

ER Collet Set

Indexa-Seiki? ER Collets are available in the in a range of sizes to maximise efficiency in most applications, they are manufactured from hardened and tempered high alloy steel. All supplied in hardwearing bench cases with protective foam inserts.

Conform to DIN 6499.
Up to 10.0mm - 0.015mm TIR.
11.0 to 18.0mm ? 0.015 to 0.020mm TIR.
19.0 to 26.0mm ? 0.015 to 0.020mm TIR.

For all technical and dimensional specifications please refer to our catalogue.