Left hand Metric HSS Ground Thread Die Nuts ISO 529

Sherwood ground thread die nuts are suitable for repairing damaged or crossed threads and clearing swarf from threads. When using a die nut (on an existing thread) it is not necessary to apply the same level of precise initial alignment required to form a new thread (i.e. with a die) as the nut will follow the existing threads. They are supplied as hexagon drive allowing them to be turned by a standard spanner or adjustable wrench without the need for a special stock.

Conform to: ISO 529

For all technical and dimensional specifications please refer to our catalogue.

Sherwood Bell-Type Centre Drills HSS

Manufactured to BS328;Part 2:1986, DIN333, ISO2540.
The "B" type Centerdrill is a dual-purpose drill which includes a 60º angle for burnishing and a 120º shoulder for chamfering. This drill is used for the heaviest of work applications.
For all dimensional specifications please refer to our catalogue.

Inch Series

Sandvik Coromant CoroDrill 880 Indexable Drilling Inserts

Guide to Geometry/Feed:
-GM geometry is the basic choice for most materials. Medium feed.
-LM geometry is the best choice for long chipping materials, e.g. low carbon steel and stainless steels. Medium feed, insert with sharp positive edge.
-GR geometry is the high feed choice for steel and cast iron. Insert with strong reinforced edge, suitable for roughing.
-GT geometry is a problem solver for unstable conditions and interrupted cuts. Low to high feed. Good chip control in most materials.

For all technical and dimensional specifications please refer to our catalogue.

CoroDrill 880 Indexable Drilling Insert

Insert size: 880.. 02 02 04H-P (Peripheral insert). Geometry: -GM. Grade 4024: steel*, stainless steel, cast iron, hardened material*.
*first choice

Guhring Drills Taper Shank HSS

General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345.

For all dimensional specifications please refer to our catalogue.

Series 245 (MT2) - Metric

Walter Titex Centre Drills HSS

Designed with spiral flutes and various lengths and forms to give high quality centre holes that suit most applications. 60 inclusive angle. Manufactured to BS328;Part 2:1986, DIN333A, ISO866, ISO2540, ISO2541.

For all dimensional specifications please refer to our catalogue.

Series K1911 - Inch

M42 Bi-Metal Bandsaw Blades

Starrett Powerband Gladiator M42 is the ultimate competitor in bi-metal bandsaw blades, providing a universal solution with optimum efficiency in large production cutting operations. A high speed steel M42 cutting edge, incorporating a new tooth design with a positive rake angle and variable pitch, combine to give Powerband Gladiator? M42 the utmost in cutting performance and cost effectiveness.

Powerband Gladiator Welded Loops

Recommended applications for Starrett Powerband Gladiator M42 bandsaw blades:
- High production cutting, full range of steels from mild to stainless up to 45 HRC, nickel-based and non-ferrous alloys
Features and Benefits:
- New tooth design features triple-tempered
- M42 high speed steel with 8% cobalt
- Rockwell C67-69
- Up to 12 positive rake angle
- Fatigue resistant alloy steel backing strip
- High wear and heat resistance
- Variable pitch teeth reduce vibration for smooth, quick cutting
- Easy penetration, excellent chip clearance, reduced noise levels
- Improved surface finish
- Faster, straighter cuts

SwissTech 2 Flute Slot Drills Weldon Shank HSS-Co 8%

Centre cutting. Weldon shank to DIN 1835B. Cutting diameter to e8. Shank diameter to h6. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 03 Long SDN-2WL TiCN Coated

Dimensions to DIN 844.

Sherwood Drills Taper Shank HSS

Suitable for single and multi-spindle drilling machines. The taper shank being the engineering industries recognised standard and most widely used method for holding and driving cutting tools. Manufactured to BS328;Part 1:1986, DIN345RN, DIN343RN.

For all dimensional specifications please refer to our catalogue.

Series T100 (MT1) - Inch

OSG Taps

OSG type 1066 machine taps are manufactured from 3% Vanadium Super Grade High Speed Steel. Increasing the vanadium content improves the toughness without making the tap brittle. This means the tap has a greater resistance to work generated heat, which prolongs the life of the cutting edge.

Spiral Flute taps are suitable for threading blind holes.

Manufactured to ISO 529: 1975.

For all technical and dimensional specifications please refer to our catalogue.

Spiral Flute Taps Metric HSS-EV

Guhring GT100 Jobber Drills HSS

HSS GT100 jobber drills. For drilling in difficult conditions when swarf congestion prevents an adequate flow of coolant. For use in steel and cast iron having a hardness of up to 1000N/mm2. Not recommended for nickel-chrome steels or similar material. Manufactured to BS 328/DIN 338.

Series 549 - Metric