Kennedy® Stub Length Drills Carbide

For drilling into steel, cast steel, cast iron, chilled cast iron, malleable cast iron, non-ferrous materials and abrasive plastic. Point angle: 118°, helix angle: 30°, tolerance of diameter: h7, tolerance of shank: h6. Manufactured to DIN 6539.

Tolerances:
Cutting Dia. plus 0.000mm - 0.015mm.
Shank Dia. plus 0.000mm - 0.030mm.

Kennedy® Carbide Stub Length Drills - Metric

Mitsubishi Indexable Turning Inserts

Grade Description: NX2525 (P01-15 K01-15)
Cermet. Outstanding grade.
Provides the best in toughness and high wear resistance. has reliability and increased tool life at higher surface speeds in steels and cast irons.

CCMT Indexable Turning Insert

Guhring GV120 Heavy Duty Stub Drills HSS-Co

Manufactured to Type GV120 DIN1897.

Series 329

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Guhring Production Drills

Guhring No.5523 Jobber Drill HSS-Co have a tough cobalt substrate that delivers high performance at low cost to produce a general purpose drill for the machining of steel and cast steel (alloyed and unalloyed), , grey cast iron, malleable cast iron, spheroidal graphite iron, sintered iron and graphite with high concentricity characteristics.

No.5523 Jobber Drill HSS-Co

Guhring Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series 205

Starrett Holesaws

Starrett tungsten carbide tipped sheet metal holesaws are ideal for cutting high alloy and stainless steels, non ferrous light metals and reinforced fabrics. The tough tungsten carbide tipped teeth, have a positive cutting angle to provide fast and efficient removal of chips and swarf, cutting depth is 13mm.

Sheet Metal Holesaws Tungsten Carbide Tipped

Starrett tungsten carbide tipped sheet metal hole saws deliver the following advantages:
Ideal for production cutting.
Tungsten carbide tipped teeth provide superb product life and cutting performance.
High cutting accuracy.
Replacement pilot drills are available.
Complete assembly - there is no requirement to purchase a separate arbor and pilot drill.
Safety stop at the base of the hole saw prevents drilling beyond maximum cutting depth.
Cutting depth 13mm (1/2").

Guhring Bushing Drills Taper Shank HSS

Standard drill for use with drill bushings and for deep hole drilling in alloyed and unalloyed steel and cast steel, grey cast iron, malleable cast iron, spheroidal cast iron, sintered powder metals, German silver and graphite. Type N DIN341.

For all dimensional specifications please refer to our catalogue.

Series 257 (MT1) - Metric

Butt-Welded Lathe Tools

Manufactured from top quality sintered steels. For use on a wide range of applications from roughing to finishing. Manufactured to BS1296:Part 3:1978.

For all dimensional and technical specifications please refer to our catalogue.

Right Angle Recessing - No.25 RH/No.26 LH

Rake and Clearance angles:
Top rake: 5.
Front clearance: 6.
Approach angle: 0.
Trail angle: 2.
Side clearance: 3.

Guhring Endmills HSS-Co 8%

Short rigid end mills to suit all general-purpose applications, including profiling centre cutting, alloyed steels, stainless steels and non-ferrous materials. Uncoated.

For all dimensional and technical specifications please refer to our catalogue.

Series 3428 4 Flute Endmills