Dormer Jobber Drills TiN Tipped

Dormer's A002 Jobber Drill has a standard helix, it is right hand and has wider flutes for efficient chip removal. 118 point geometry. TiN coated on the tip for high wear resistance, lower friction and allows increased cutting speeds. Suitable for general-purpose drilling.
The Dormer A002 Jobber drill delivers the following features and benefits:
Improved web design optimises strength and rigidity and increases feed capability
Ground wide flutes allow for efficient chip evacuation
Optimised throughout the helix range for greater rigidity
Bright body improves application on ductile materials
Titanium Nitride coating focused on the working surfaces to resist flank and crater wear, and to provide low friction and increased performance
Special Dormer P.S. Point increases ease of penetration, improves hole size and provides accurate centering
General purpose engineering drills
Manufactured to BS328:Part 1:1986.

Series A002

Kennedy® Ball Nosed Slot Drills Plain Shank Carbide Micrograin

For maximum strength when milling harder materials where rapid swarf removal is not needed. 4 flute milling cutters have one of the strongest tooth structures available in solid cutters. Centre cutting as standard. Manufactured to ANSI Standards.

For all dimensional and technical specifications please refer to our catalogue.

Long Series - 4 Flute - Inch

For maximum strength when milling harder materials where rapid swarf removal is not needed. 4 flute milling cutters have one of the strongest tooth structures available in solid cutters. Centre cutting as standard. Manufactured to Ansi Standards.
Inch Tolerances
Nominal Limits Of Tolerance
Diameter High Low
1/16" - 1/4" 0.000 -0.002
17/64" - 1" 0.000 -0.003
Metric Tolerances
Nominal Limits Of Tolerance
Diameter High Low
1 - 6 0.000 -0.050
7 - 25 0.000 -0.080

M42 Bi-Metal Bandsaw Blades

Powerband II has an M42 high speed steel cutting edge giving greater hardness and heat resistance. Increases blade life when cutting such materials as austenitic stainless steels, nickel base alloys, titanium and similar tough od high hardness metals. Available as Regular, Hook and Variable Pitch teeth. Manufactured to BS3877-1991.

Powerband II Welded Loops

For all technical specifications please refer to our catalogue.

Sandvik Coromant CoroDrill 880 Drill Bodies

Stronger drill body with new surface treatment can withstand higher feeds. Wiper geometry for best surface finish. Optimized chip channels for accelerated chip evacuation. Easy identification due to laser marking with drill-, insert- and screw codes on the drill shank.

For all dimensional/technical specifications and for a full range of available Inserts, please refer to our catalogue.

Cylindrical shank - flat according to ISO 9766.

CoroDrill 880 Drill Bodies

Sherwood Long Series Drills Steam Tempered HSS

General-purpose drills to drill steels with tensile strength up to 1,000N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118, helix angle: normal, web thickness: normal, relief angle: 10-20, tolerance of diameter: h8, tolerance of f11. Manufactured to BS328;Part 1:1986, DIN340RN, ISO494.

For all dimensional specifications please refer to our catalogue.

Series L100 - Metric

OSG Endmills Carbide

OSG WX-EMS short series 4 flute endmills are manufactured from high performance micro grain carbide with an Ultra WX coating (multi layered composite TiALN).

Centre cutting.
Cutting length: 1.5 x D.

The Ultra WX coating has been developed to improve performance in a wide range of materials including nonferrous materials, mild steels, and refined steels This stable performance remains consistent in both wet and dry applications and is intended for a wide range of cutting conditions, from low speed/reduced cutting force applications to high speed/high cutting force applications.

For all technical and dimensional specifications please refer to our catalogue.

WX-EMS Series 4 Flute Endmill 30 Helix Plain Shank Carbide

Starrett Bi-Metal Holesaws Constant Pitch HSS

Bi-Metal Constant Pitch Holesaws have 6 teeth per 25mm/inch with an aggressive cutting action, featuring a HSS cutting edge welded to a tough alloy steel body. The Constant Pitch provides a smooth cut on thinner gauge materials, with minimal tendency to bite or snag on contact with irregular surfaces. Cutting depth 41mm (1 5/8").

Holesaw and Arbor sizes:
14-25mm - use Arbor A4 or K4.
30-210mm - use Arbor A10 or K10.

Constant Pitch Bi-Metal HSS Holesaws

Indexa-Seiki? XP-45C ?Hi Shear? Milling Cutters

Super Positive 45 approach milling cutter, angle decreases cutting forces and allows a quick feed in a limited capacity machine. Torx screws allow for good chip evacuation. Plasma Ion coating offers longer tool life and greater hardness that is more resistant to wear. Through coolant as standard.

Walter Titex Centre Drills HSS

Designed with spiral flutes and various lengths and forms to give high quality centre holes that suit most applications. 60 inclusive angle. Manufactured to BS328;Part 2:1986, DIN333A, ISO866, ISO2540, ISO2541.

For all dimensional specifications please refer to our catalogue.

Series K1911 - Inch

Sherwood Ground Thread Chasers HSS

Used for the lathe turned production and repair of threads.

For all technical specifications please refer to our catalogue.

Hand

Whitworth Form