Allied Maxcut Series 0 and 0.5 Holders

Diameter range: 12.98 to 17.65mm.

For all dimensional specifications please refer to our catalogue.

Flanged Straight Shank

SwissTech 3 Flute 37 Coarse Pitch High Helix Roughing Endmills for Aluminium HSS-Co 8%

Centre cutting. Weldon shank to DIN 1835B. Shank diameter to h6. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 20 Regular RHH-3WR HSS-Co 8%

Dimensions to DIN 844.

Kennedy® Ball Nosed Slot Drills Plain Shank Carbide Micrograin

For maximum strength when milling harder materials where rapid swarf removal is not needed. 4 flute milling cutters have one of the strongest tooth structures available in solid cutters. Centre cutting as standard. Manufactured to ANSI Standards.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 4 Flute - Inch

For maximum strength when milling harder materials where rapid swarf removal is not needed. 4 flute milling cutters have one of the strongest tooth structures available in solid cutters. Centre cutting as standard. Manufactured to Ansi Standards.
Inch Tolerances
Nominal Limits Of Tolerance
Diameter High Low
1/16" - 1/4" 0.000 -0.002
17/64" - 1" 0.000 -0.003
Metric Tolerances
Nominal Limits Of Tolerance
Diameter High Low
1 - 6 0.000 -0.050
7 - 25 0.000 -0.080

ISCAR Parting & Grooving Blades

ISCAR Tang-Grip? uses a single-ended insert for parting, with a revolutionary clamping method (patent pending). Very rigid clamping is achieved in a tangentially oriented pocket. This increases pocket life by 3 times more than any other SELF-GRIP mechanism.

Tang-Grip? TGFH Parting & Grooving Blades

ISCAR Tang-Grip? has the following features:

? Enables machining at high feed rates and provides excellent straightness and surface finish.
? Provides a solution to the problem of inserts being pulled out during retraction. Has a solid stopper, unlike the friction retaining force in the current systems. (Especially important on machines with a bar feeder or sub spindles.)
? In the SELF-GRIP? system the machining forces are exerted on a very short stopper, while in the TANG-GRIP system, machining forces are supported by a long and rigid rear wall. Pocket wear, which occurs during machining and insert indexing in the SELF-GRIP? system, causes a reduction in the clamping force. This does not happen with the new TANG-GRIP? system.
? The TANG-GRIP? system provides very accurate grooving repeatability.
? The combination of tangential clamping and free chip flow results in improved tool and pocket life.
? Offers a free, unobstructed chip flow. This is very important in deep grooving, since there is no upper jaw to interfere as in the other clamping systems.

For all technical specifications and inserts please refer to our catalogue.

Indexable Boring Bar Sets

This toolholder is supplied complete with 10 Carbide inserts, either P Grade for steels and general use, or K Grade for cast iron and non-ferrous applications.

Type of inserts subject to availability.

SDUCR Boring Bar with 10 Inserts

93° approach. Uses DC_T Inserts. For boring bar details see IND-106-7660K/-7720K.

Dormer Stub Drills

The A120 HSS stub drill from Dormer has a standard helix right hand spiral. The rigidity of these Dormer stub drill bits allow them to be used in portable drills, turret and automatic lathes.

Series A120 Stub Drill HSS - Metric

Dormer Jobber Drills Solid Carbide

General-purpose carbide drills. 120 four-facet point for accurate centering and improved hole quality. Bright finish.

Series R100 - Metric

Granlund Size 1 Toolholders

Type S with Rotating Depth Stop.

For further specifications please refer to our catalogue.

Swiss+Tech® HSS "Green Ring" Taps

Manufactured to DIN 371/376

Fluteless - HSS-EV Nitride Finish (TiN coated) ISO Metric Coarse

For through and blind holes. Taper lead to DIN form B (4 x P). Tapping tolerance to 6H.

SEKN

K20 (ISO K20) Micrograin Uncoated. For Cast Irons, Aluminium Alloys, other Non-Ferrous materials including Titaniums and Nickel Alloys.

1203

To suit: Indexa-Seiki face hog milling cutter. Hitachi 45° face mill.