SwissTech Heavy Duty Jobber Drills HSS-Co 8% Cobalt

The addition of up to 8% Cobalt allows higher speeds to be used without reducing the life of the tool, increasing productivity. 28 Helix and 135 Point. Manufactured to DIN338RN. Point to DIN1412C.

Series 1020 - Metric

Kennedy Rasps

Designed for general use and best suited to softer materials such as wood, plastics, fillers, leather and lead.

Cabinet

Bastard Rasp Cut

BSW (British Standard Whitworth) HSS Ground Thread Dies

Sherwood dies are for use in die stocks to cut external screw threads on metal rod, the split in the die allows the adjusting screws of the diestock to compress or expand the die to accommodate for slight variations in size of the material being threaded or die sharpness. Sherwood dies are available as Metric Fine, Metric Coarse, UNF, UNC, BA, BSF, BSW, BSPT, BSPF, NPT cutting threads all the dies are manufactured from HSS with precision ground threads to the applicable standard.

For all technical and dimensional specifications please refer to our catalogue.

Die BSW (British Standard Whitworth) Ground Thread HSS

Manufactured to: BS1127
Thread Form to: BS84

Sherwood Die Nuts

Sherwood ground thread die nuts are suitable for repairing damaged or crossed threads and clearing swarf from threads. When using a die nut (on an existing thread) it is not necessary to apply the same level of precise initial alignment required to form a new thread (i.e. with a die) as the nut will follow the existing threads. They are supplied as hexagon drive allowing them to be turned by a standard spanner or adjustable wrench without the need for a special stock.

Conform to: ISO 529

For all technical and dimensional specifications please refer to our catalogue.

Die Nuts Metric Fine HSS

Kennedy® Thredfloer Fluteless Taps

Form rather than cut the thread in almost any ductile material. These include aluminium, brass, copper, carbon steels, zinc and magnesium alloys and even some stainless steels. The material is "cold formed" into the relevant thread and has the advantage of being a full form thread unlike normal cut tapped holes. This make the thread stronger. The forming operation does not create chips so swarf contamination and blockage is illiminated and tap breakage reduced. Because there is no consideration for chip evacuation, Thredfloer taps can be run at higher cutting speeds and reduced cycle times. Lubrication grooves are a feature of all Thredfloer taps of M3.0 and over. These allow lubrication to reach the end of the tap to maintain tool life and to prevent damage from "Hydraulic Blow Out".

Metric Coarse

HSS - EV. Oxide Finish. Tolerance 6H. Manufactured to DIN 371.

SwissTech 2 Flute Q-Coat Slot Drills Plain Shank Carbide

Centre Cutting. To Manufacturers Standards. Cutting diameter to h10, Shank diameter to h6. ?Q-Coat? Coating has been specifically developed to give carbide cutters the ?edge? when faced with severe machining conditions. Materials up to 66 HRC. Dry cutting. Die and Mould machining. Reduced coolant usage and disposal. Up to 100% longer cutter life. Reduced manufacturing costs. A multi-layer coating capable of operating at higher speed and feed. Excellent oxidisation resistance. High speed machining. Surface hardness 3300HV. Surface coefficient against steel 0.25. Thickness of coating 305um. Maximum working temperature 850. Re-coating service also available.

For all technical and dimensional specifications please refer to our catalogue.

Series 74
Long Reach

HSS-Co 8% Plain Shank Milling Cutters 2 Flute

Centre cutting, used for profile milling, milling keyways and producing open slots. Surface treatment: bright finish.
Flute type: 30° Helix. Overall dimensions to DIN 844. Plain shank to DIN 1835A.

Regular Length

Iscar HELITURN Indexable Inserts

Iscar HELITURN LD Inserts with High Helical Cutting Edge for High Metal Removal Rates. The HELITURN LD inserts WNMX ...-HTW and CNMX ...-HTW are produced from the most advanced SUMO TEC grades. These inserts are designed with very positive radial helical cutting edges and positive rake angles ? a combination which substantially reduces the cutting forces and facilitates higher productivity.

The CNMX and WNMX insert corners are equipped with a wiper configuration which produces high surface finish, even at high feeds.

In many cases the surface finish is sufficient for eliminating a finishing cut.
HELITURN LD inserts were designed for heavy machining applications. Their unique design ensures reliable, Fast Metal Removal.

ISCAR has recently added the HMW chipformer for machining stainless steel, high temperture alloys and soft, low carbon steel.

CNMX and WNMX inserts require special tools with appropriate seats.

WNMX HELITURN Indexable Inserts

Grade Description: IC807 A tough submicron substrate improved TiAIN PVD coated grade for better chip flow. Suitable for turning heat resistant alloys, austenitic stainless steel and hard steel at low to medium cutting speeds

Alliee Maxcut Series Z Inserts

For all dimensional specifications please refer to our catalogue.

GEN2 T-A HSS Super Cobalt AM200 Coated

Indexa-Seiki? Lever Lock External Toolholders

For further technical and dimensional specifications please refer to our catalogue.

PSDN N

45 Straight Approach for negative square inserts.