Guhring Stub Drills HSS

Ideally suited for portable drill applications where the shorter flute and stub length offer the extra rigidity normally associated with fixed drilling. Manufactured to BS328:Part 1:1986/DIN1897RN.

Series 223

Sandvik Coromant CoroDrill 880 Drill Bodies

Stronger drill body with new surface treatment can withstand higher feeds. Wiper geometry for best surface finish. Optimized chip channels for accelerated chip evacuation. Easy identification due to laser marking with drill-, insert- and screw codes on the drill shank.

For all dimensional/technical specifications and for a full range of available Inserts, please refer to our catalogue.

Cylindrical shank - flat according to ISO 9766.

CoroDrill 880 Drill Bodies

Starratt Bandsaw Blades

Super Flex-Back is recommended for general-purpose cutting at an attractive cost on easy to machine materials; blades have excellent fatigue endurance to give long life on machines running at a high surface feet per minute. High carbon/chromium `pinpoint carbide` tool steel. Hardened and tempered tooth tips - 64/66 Rockwell C Hardness. Economical, general-purpose cutting. Recommended applications: light section low alloy steels, ferrous and non-ferrous metals, plastics, furniture and composition board.

Kennedy Endmills

Kennedy KC3 throwaway 3* flute endmills are manufactured HSS-Co 5% making them much tougher than HSS. This means that Kennedy endmills can be used at higher speeds and feeds which in turn gives greater productivity.

Kennedy KC3 endmills are available uncoated, TiN coated and TiCN coated.

TiN (Titanium nitride) provides a surface hardness in the region of 2300HV which offers improved wear resistance, tool life and productivity.

TiCN (Titanium Carbonitride) gives a surface hardness in the region of 3000-3500 HV, excellent wear resistance and good heat resistance. This coating is used for the same things as TiN but also for hard steels, stainless, cast iron, brass & bronze.

For all technical and dimensional specifications please refer to our catalogue.

*Except: 1mm cutters, 2mm and 1/16" ball nose cutters, all of which have two flutes.

KC3 Endmill Long Series 3* Flute Throwaway Cutter Weldon Shank HSS-Co 5% - Metric

Dijet Carbide End Mills

Dijet AL-SEELS series End Mills are for profiling & Slotting in Aluminium and Alloys

AL-SEEL-2 Long Series Carbide End Mill

Dijet AL-SEELS series Carbide end mill specification:
Sharp corner.
Helix angle 45.
2 flute.
Centre cutting.
Regular cutting edge.
Shank cutting diameter to 0.04-0.0
Weldon shank to DIN 1835B.

Dormer Taps

Dormer MTT-X Series taps are manufactured from HSS-X1 Steel with a Bright finish, they are right Hand Cutting.

Manufactured to ISO 529
Spiral Flute for threading blind holes.
Taper lead to DIN form C.
Tapping tolerance to 6H.
Max Depth 2.5 x D.
Helix angle 48.

For all technical and dimensional specifications please refer to our catalogue.

MTT-X Series E023 Spiral Flute UNC (Unified Coarse) Tap

SS-Co 5% 3 Flute Piloted Countersinks

For the production of high precision concentrically centred countersinks in most metals where pilot holes have been pre-drilled.
Shank diameter: 3/16”.

Sandvik Coromant CoroDrill 880 Indexable Drilling Inserts

Guide to Geometry/Feed:
-GM geometry is the basic choice for most materials. Medium feed.
-LM geometry is the best choice for long chipping materials, e.g. low carbon steel and stainless steels. Medium feed, insert with sharp positive edge.
-GR geometry is the high feed choice for steel and cast iron. Insert with strong reinforced edge, suitable for roughing.
-GT geometry is a problem solver for unstable conditions and interrupted cuts. Low to high feed. Good chip control in most materials.

For all technical and dimensional specifications please refer to our catalogue.

CoroDrill 880 Indexable Drilling Insert

Insert size: 880.. 08 05 W10H-P (Peripheral insert). Geometry: -LM. Grade H13A: non-ferrous material.

Iscar Turning Inserts

IC9250 Grade description (P20 - P30, M15 - M30).
A TiCN/Al2O3/TIN multi-layer, CVD coated grade. Especially recommended for grooving and turning forged, low carbon and low-alloyed steel parts. Copes efficiently with machining stainless steel at finishing and medium conditions.

WNMG

Kennedy Toolbits & Parting-Off Blades

Cut faster, 'stand up' longer and reduce costs. Square and rectangular toolbits supplied with 10 bevelled ends. Parting off blades supplied with 2 side taper, 15 bevel (top and bottom).

5% Cobalt Rectangular Inch